manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

9.40

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Protocols

Serial Distributed Network Protocol (Serial DNP3)

in the connected device. For example, an SEL-421 Relay provides SER data 
with a –0/+2 ms accuracy and 1 ms time-stamp resolution and that data 
becomes DNP3 events in the SEL-2032. This system also supports two-tier 
SEL-2032 applications. 

Figure 9.4

 illustrates the flow of SER data.

Figure 9.4

SER Data Flow

For devices and data that do not support the SEL Fast SER protocol including 
SEL equipment without an internal SER function, non-SEL equipment, and 
analog data from any device, the SEL-2032 generates DNP3 event objects 
(Object 2 and 32) by scanning the Port 16 User Region. This results in an 
average time-stamp accuracy of approximately (–0/+0.25 seconds plus one- 
half of the device polling time) for an overall approximate accuracy of –0/+1 
second.

To determine if your SEL device supports the Fast SER protocol, consult the 
Instruction Manual or connect the SEL device, perform an autoconfiguration 
on the SEL-2032 port connected to the device, and issue the 

AUTO

 command. 

For equipment that supports the Fast SER protocol, you will see Binary 
Unsolicited listed under SER Support as shown in 

Figure 9.5

.

SEL-2032

SEL

SEL

GPS Clock

SEL-421

SEL Relay

SCADA Master

SEL-2032

SEL-421

SEL Relay

Lower-Tier

Fast SER

Data

Relay

Fast SER

Data

DNP Events with

SER Quality
Timestamps

Local HMI Using

 SEL Protocol Driver

Station-Wide

Fast SER

Data

2

3

1

SEL

. . .

. . .

Relay 

Fast SER 

Data

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Brand: Paradyne Pages: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 5
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46
Supero Supero SAS-826A User Manual preview
Supero SAS-826A
Brand: Supero Pages: 16
B&B Electronics Parallel Printer Card PIOC User Manual preview
Parallel Printer Card PIOC
Brand: B&B Electronics Pages: 16
Renesas Emulator MCU Board for 38D5 Group M38D59T-RLFS User Manual preview
Emulator MCU Board for 38D5 Group M38D59T-RLFS
Brand: Renesas Pages: 4
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Brand: ZALMAN Pages: 9
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Brand: Danville Signal Processing Pages: 35
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Brand: Advantech Pages: 96
Bailey INFI 90 NTAI06 Instruction preview
INFI 90 NTAI06
Brand: Bailey Pages: 33
Aaeon GENE-EHL7 User Manual preview
GENE-EHL7
Brand: Aaeon Pages: 119
Crest Audio NC-MCO - TECHNICAL Technical Data preview
NC-MCO - TECHNICAL
Brand: Crest Audio Pages: 2
Renesas R8C/2F Quick Start Manual preview
R8C/2F
Brand: Renesas Pages: 6
Genexis FiberTwist XGS2420 Installation Manual preview
FiberTwist XGS2420
Brand: Genexis Pages: 7
TERSUS Precis-BX305 Quick Start Manual preview
Precis-BX305
Brand: TERSUS Pages: 7
Yeastar Technology YE110 Instruction preview
YE110
Brand: Yeastar Technology Pages: 2

Brands by name

Popular brands

Load more brands