background image

Page 6

Minimum Mounting Height

This fan unit is intended for mounting at a minimum 
height of 2.1 metres (measured to the lower part of 
the fan impeller) above a floor or the ground.

Avoidance of Back Flow

Care should be taken to avoid the back flow of gases 
into the room from the open flue of gas or other open 
fire appliances.

Replacement of supply cord

If the supply cord is damaged, it must be replaced by 
a service agent or suitably qualified person in order to 
avoid a hazard.

NOTE: 

Do not use with a timer.

Why Flexi-duct?

Some internet sites strongly recommend the 
use of rigid ducting over fully flexible ducting. 
This may well be the case with conventional 
rangehoods with internal motors but not with 
external motor rangehood.

Schweigen’s unique Isodrive system works in the 
opposite way to conventional rangehoods, pulling air 
through the hood and acoustically matched ducting, 
producing almost silent high volume flow. The use 
of a complete rigid or semi-rigid ducting system will 
allow an organ piping effect to occur; like a didgeridoo 
where a noise is produced at one end of a hollow rigid 
pipe and the noise is amplified out the other.

The Isodrive system drives the noise outside the 
house.

WARNING:

 

Installation without the use of at least the minimum 
recommended length of acoustically matched 
flexi-ducting in the system will void performance 
expectations. Any installation problem must be 
reported to Schweigen. Call outs relating to incorrect 
installation will result in a service fee direct to the 
customer. Schweigen takes no responsibility for 
problems caused by faulty installation, this may void 
warranty. 

A preferred installer list can be obtained from 
Schweigen website 

www.schweigen.com.au

 or 

by calling 

1300 881 693

.

2. Your Safety

Summary of Contents for Endline Isodrive 1350





















Reviews: