USER MANUAL ZHS04
PLUG-IN SWITCH
INDOOR
ZHS04
BDA_ZHS04_b
HOME AUTOMATION
Congratulations and thank you for purchasing the Schwaiger
ZHS04 product. Below you will find useful operating guide-
lines.
Product description
This is a switch actuator, which is used as an adapter plug between standard
Schuko sockets (connector type F) and cable-connected electrical loads up to
a load of 3500 W. The device with protection class IP 20 can only be used in
dry interior spaces. It is operated via a pushbutton on the device or via Z-Wave
commands. The state of operation is indicated by a LED on the device. The
colour choice can be freely configured. Every change of the switching status -
no matter whether triggered wirelessly or locally, will be reported to a central
gateway.
A built-in virtual power meter records the electrical energy consumed when the
rated load of the connected load is correctly specified in a configuration param-
eter. The pushbutton can be used both for switching the device itself as well
as to control other devices wirelessly. Single and double clicks are recognized
and distinguished.
Please read the guidelines before installation!
Only use the device as specified in the manual. The manufacturer undertakes
no warranty for improper use.
Installation guidelines
The plug adapter switch can be used in any standard grounded outlet. Due
to the IP20 protection class the plug adapter switch can only be used in dry
interior spaces. For reasons of overheating the unit should not be exposed to
direct sunlight and the ambient temperature should between 0° C and 40° C.
Performance of the device in the Z-Wave network
When delivered, the device is not connected to a Z-Wave network. It must be
integrated into an existing Z-Wave network so that it can communicate with
other Z-Wave devices. This process is called Z-Wave inclusion. Devices can
also be removed from networks again. This process is called Z-Wave exclusion.
Disposal information
This device doesn‘t contain any batteries. It is an electrical device. It can be
disposed free of charge at specified disposal sites.
EC Declaration of Conformity
„Hereby Schwaiger GmbH declares that the product ZHS04 is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/EC.“ The Declaration of Conformity can be found at the following ad-
dress: http://www.schwaiger.de/downloads
Control button
LED status
Logging in
(inclusion)
Press the control button
three times in quick
succession
Logging out
(exclusion)
Press the control button
three times in quick
succession
Operation of the device
The device can be used for electrical appliances, such as HV halogen lamps,
LV halogen lamps, fluorescent lamps and incandescent lamps, with a switching
capacity of up to 3500 W. It can be operated either wirelessly via a controller
(wireless remote control/wall switch) or directly via the pushbutton on the
wireless adapter plug. The switching status is indicated by a red LED on the
pushbutton.
Meaning of the LED signals
green light = off
blue light = on
Both processes are started from a controller that must be connected to an
inclusion and/or exclusion mode. The manual of the controller contains infor-
mation on how it is to be connected in these modes.
Devices can only be added when the controller of the Z-Wave network is in
inclusion mode. Leaving the network by exclusion will reset this device to its
factory defaults.
The product is delivered as „not programmed.“ To set up the wireless adapter
plug you need a controller.
Technical specifications
Electricity supply
230V ~50-60 Hz
Switchable loads
16 A (3500 W)
Protection class
IP20
Explorer Frames
Yes
SDK
4.5
Type of equipment
Slave with routing capabilities
General Z-Wave device type
Binary switch
Special Z-Wave device type
Binary power switch
Router
Yes
FLiRS
No
Firmware Version
1.0
MANUFACTURER INFORMATION
Dear Customer,
should you require technical advice and your
retailer could not help please contact our
technical support.
Schwaiger GmbH
Würzburger Straße 17 90579 Langenzenn
Hotline: +49 (0) 9101 702-199
www.schwaiger.de [email protected]
Business hours:
Monday to Thursday:
08:00 - 17:00
Friday:
08:00 - 14:30
Logging in (inclusion) or logging out (exclusion) of the plug
By pressing the control button three times in quick succession you confirm the
inclusion and exclusion of the device.
