the batteries, if the appliance is not to be used for long while,
to prevent leaking. Leaking or damaged batteries might cause
acid burns if the come into contact with the skin. Therefore,
use suitable protective gloves. Make sure that the batteries are
not short-circuited. Do not throw batteries into a fire. Batteries
(non-rechargeable) must not be recharged. There is danger of
explosion.
Switching the Inspection camera On and Off
Press the On/Off Switch (2). The Inspection camera turns on. After
a short time, the camera image appears on the monitor. To turn off,
press the On/Off Switch again. The device turns off.
Camera lighting
To enable the Inspection camera to be used in totally dark areas,
the camera head camera has an integrated, stepwise, dimmable
LED light.
Press the button „brighter“ (3), to switch on the light. Now, each
time you press the button the light becomes brighter. You can
reduce the brightness, or switch off the light, by pressing the button
„darker“ (4). Now, each time you press the button the light
becomes darker. Adjust the lighting, so that the image displayed on
the monitor is not over-exposed or underexposed. Press the On/Off
Switch, to turn the device off (2). The device turns off.
To Rotate the Camera Image by 180°
By using a key combination, the camera image can be rotated by
180°. This facilitates the control of the camera image in
unfavourable positions. In normal camera mode, press the buttons
„brighter“ (3) and „darker“ (4) at the same time. The camera image
will be displayed on the monitor rotated by 180°. This function is
automatically deactivated when the device is switched off.
NTSC video output
The Inspection camera has the option to display the image for
recording and documenting, using an integrated NTSC video
output.
The Video-Out jack is located on the underside of the handle (1).
Please use the video cable supplied to connect to your play back or
recording device. Switch the Inspection camera on. Plug the phono
jack in the socket (1) of the Inspection camera. Connect the RCA
connectors to the video input of your play back or recording device.
Then switch the play back device on and select the video input.
For proper replay of the NTSC video signal, you will
need a multisignal device. Modern devices have auto-
matic video signal detection. If not, set the video input
manually to „NTSC“. Please follow the instructions in the
operating manual for your playback or recording device.
The
camera image will be displayed, if you have connected the device
properly and if you are using the correct video source. Press the
On/Off Switch, to turn the device off (2). The device as well as the
video output are turned off.
Magnetic and Hook Attachments
The magnetic and hook attachments can be placed on the camera
head. In this way, lost metal parts can be searched for and found.
Maintenance and Cleaning
You do not need to service the product, apart from occasional
cleaning. Use a soft, antistatic and lint-free cloth for cleaning. Do
not use abrasive or chemical cleaners. Carefully rinse the
gooseneck of the Inspection camera with clean water, after use in
liquids and dry it before storing it in the case.
Disposal
Electronic products are raw material and do not belong in
the household waste. When the device has reached the
end of its service life, please dispose of it, according to
the current statutory requirements, at your local collecting
site. Disposal in the domestic waste is not permitted!
Disposal of used batteries
As a consumer you are required
(Battery Ordinance)
to
responsibly dispose of all used batteries and
rechargeable batteries;
do not dispose of used
batteries in the household waste!
You can return used
(rechargeable) batteries free of charge at the official
collection points in your municipality, our stores, or where
ever (rechargeable) batteries are sold!
You thus fulfil
the legal requirements and make your contribution to
protecting the environment!
Technical Data
TFT monitor 6 cm (2.4“) Screen size
Resolution 320 x 234 pixels
Focus 30 mm
Field of view 54 °
White Balance automatic
Exposure automatic
Camera lighting 2 LEDs, white
Video format NTSC
Gooseneck Length approx. 90 cm
Min. bending radius 45 mm
Camera Diameter 10 mm
Protection Class gooseneck IP67 (waterproof)
Power Supply 6 V/DC (4 x AA)
Power input max. 200 mA
Weight without accessories approx. 370 g
Ambient/ operating temperature 0 to +45°C
Schwaiger GmbH – Würzburger Strasse 17 – 90579 Langenzenn
www.schaiger.de – [email protected] - Tel. +49 9101 – 702-0
