OPERATION
SBX-75/87 04/19
Operation Section 4-15
© 2019 Alamo Group Inc.
OPERA
T
ION
4. Turn off the tractor engine and dismount.
5. One lift arm at a time, attach the tractor lower
link arms to the snow blower lower link pins.
Then install lynch pins in the ends of the lower
link pins.
6. Extend or retract 3-point top link to align its end
hole with the holes of the snow blowers top link.
Insert the top link hitch pin and insert lynch pin
into hitch pin to hold the upper top link.
7. Check that the snow blower is level side to side.
Adjust tractor lift link if necessary.
8. Adjust any lower link check chains, guide
blocks, or sway blocks to prevent the snow
blower from swaying side to side and possible
contact with tractor rear tires.
Carefully raise and lower the snow blower and check for any possible interference between
the snow blower and tractor. Turn discharge chute full right. Make adjustments if necessary.
Before operating the snow blower, carefully read the
Safety and Operation Sections
of
this Operator’s Manual.
Always shut the Tractor completely down, place the transmission in park, and set the
parking brake before you or anyone else attempts to connect or disconnect the Implement
and Tractor hitches.
(S3PT-15)
Never work under the Implement, the framework, or any lifted
component unless the Implement is securely supported or blocked up
to prevent sudden or inadvertent falling which could cause serious
injury or even death.
(SG-14)
There are obvious and hidden potential hazards in the operation of this Implement as in all
power-driven or pulled equipment. REMEMBER! This machine is often operated in rough
terrain conditions that include gullies, holes, slopes, hidden obstructions and the like.
Serious injury or even death may occur unless care is taken to assure the safety of the
operator and bystanders in the area. Do not operate this machine with anyone in the
immediate area. Stop operating if anyone comes within 200 feet of the equipment.
(SSB-34)
Summary of Contents for SBX-75/87
