SCHOTT ColdVision Light Source Programming Manual Download Page 6

Page: 6 / 33

Legacy Protocol

D20980.026 Rev B

CV-LS Programming Guide

Page 6

Command Index

System Status ............................................................................................... 9

1.1

Temperature .......................................................................................................................9

1.1.1

Board ..................................................................................................................................... 9

1.1.2

LED ........................................................................................................................................ 9

1.2

Voltage Monitors .............................................................................................................. 10

1.2.1

Input .................................................................................................................................... 10

1.2.2

Reference 5V Output .......................................................................................................... 10

1.3

Fan ................................................................................................................................... 10

1.3.1

Speed................................................................................................................................... 10

1.3.2

Status .................................................................................................................................. 11

1.4

Equalizer ........................................................................................................................... 11

1.4.1

Stability ............................................................................................................................... 11

1.4.2

Status .................................................................................................................................. 11

1.5

System Information ........................................................................................................... 11

1.5.1

System Mode ...................................................................................................................... 11

1.5.2

User Mode ........................................................................................................................... 11

1.5.3

Time .................................................................................................................................... 12

1.6

Light Feed Back Raw .......................................................................................................... 12

1.7

Error Flags ......................................................................................................................... 12

1.8

Inputs ............................................................................................................................... 12

1.8.1

Analog ................................................................................................................................. 12

1.8.2

Digital .................................................................................................................................. 12

1.9

Identification .................................................................................................................... 13

1.9.1

Product Name ..................................................................................................................... 13

1.9.2

Firmware Revision ............................................................................................................... 13

1.9.3

Serial Number ..................................................................................................................... 13

1.9.4

Model .................................................................................................................................. 13

1.9.5

Model:Serial ........................................................................................................................ 13

1.10

Memory Write Cycles ........................................................................................................ 14

1.10.1

Factory Settings ................................................................................................................... 14

1.10.2

User Settings ....................................................................................................................... 14

1.10.3

SPI (Firmware Uploads) ....................................................................................................... 14

1.10.4

Error Logs ............................................................................................................................ 14

Configurations ............................................................................................ 15

2.1

Persistent Memory ............................................................................................................ 15

2.1.1

Save Settings ....................................................................................................................... 15

2.1.2

Restore Settings .................................................................................................................. 15

Summary of Contents for ColdVision Light Source


































Search results

Summary of Contents for ColdVision Light Source

Reviews:

Related manuals for ColdVision Light Source

Brands by name

Popular brands

SCHOTT ColdVision Light Source, Programming Manual

Search results

Summary of Contents for ColdVision Light Source

Reviews:

Related manuals for ColdVision Light Source

Brands by name

Popular brands