background image

 
 

Legacy Protocol 

Settings 

 

 

D20980.026 Rev B 

CV-LS Programming Guide 

Page 27 

4.2

 

Network 

4.2.1

 

Connection Status 

&AU? 

Gets the network interface’s connection status.  
Return string: 

&auX  

Return value (

X

): 1 = Net Connection Present, 0 = No Net Connection 

 

Note:

 Current driver does not support this function, so command will always return 

&au1

4.2.2

 

Hostname 

&AH# 

Gets/Sets the network host name of the unit. This string appears in the network finder 
application, and can be used to distinguish units on the network.  
Input Options (#): Host Name String (no space), ? = Query 
Return string: 

&ahX  

Return value (

X

): Host Name String 

4.2.3

 

DHCP 

&AM# 

Gets/Sets if DHCP is enabled. 
Input Options (#): 0 = Disabled, 1 = Enabled, 2 = Restart Stack, ? = Query 
Return string: 

&amX 

Return value (

X

): 0 = Disabled, 1 = Enabled, 2 = Restarting Stack 

4.2.4

 

IP Address 

&AID? 

Gets the network interface’s Dynamically assigned IP.  
Return string: 

&aidX  

Return value (

X

): IP in format “xxx:xxx:xxx:xxx” 

 

Note:

 If DHCP is disabled command will return “000:000:000:000” for the IP address. 

Note: 

Unit will accept command without (?) for backwards compatibility. 

 

 

&AIS# 

Gets/Sets the network interface’s static IP.  
Input Options (#): IP address, ? = Query 
Return string: 

&aisX  

Return value (

X

): IP in format “xxx:xxx:xxx:xxx” 

 

Note: 

Unit will accept IP addresses separated with “:” and leading 0’s for backwards 

compatibility, but will also accept standard format IP addresses. 

 

 

Summary of Contents for ColdVision Light Source


































Reviews: