background image

© 2011 Ingersoll-Rand Company
1-877-671-7011
Printed in U.S.A.

 

941128-00 Rev. 7/11_b

941128-00

672 Series TouchBar

INSTALLATION AND WIRING MANUAL

GENERAL DESCRIPTION:

The 672 Series Request to Exit TouchBar is a non-latching releasing device. It is most

often used as a switch to release a magnetic lock. A double pole output is standard, and allows for use when
integrating with a monitoring system which requires a signal for legal egress. The device can be ordered to fit 3
standard door openings or can be cut to size in the field. A 24-inch (minimum) pre-connected cable comes standard
to make installation easier.
These devices are to be installed in accordance with the applicable codes and the local authorities having jurisdiction.
It is up to local authority having jurisdiction whether this is to be installed in lieu of panic hardware. 

WHAT MODEL DO YOU HAVE?

EXAMPLE: 672-36-628-RD-RHR-WD

DOOR WIDTH:
36”
42”
48”

PUSHPAD:
RD 

Black Pushpad w/ RED letters

GID

Glow-in-dark

OPTIONS:
AR

18” armored door cord (no wire)

WD

Sex nuts/screws for wood or hollow metal door applications

SHK

Aluminum door mounting shim kit (screws included)

TYPICAL INSTALLATION:

BAR FINISHES:
628

Satin aluminum

313

Dark Satin Bronze

HANDING: 
RHR or LHR (Shown above) to change
hand (if required) see page 2.

Summary of Contents for 672 Series







Reviews: