Schiller CARDIOVIT AT-2 Service Handbook Download Page 63

Page: 63 / 109

Page 5.3

Chapter 5

Adjustments

SCHILLER AT-2 6-Channel ECG Unit

SERVICE HANDBOOK Issue 2.1 November 1998

123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234

Warnings, Cautions and Conditions

WARNING

MAINS POWER IS POTENTIALLY LETHAL - DISCONNECT THE MAINS BEFORE

DISASSEMBLING THE UNIT. ADDITIONALLY ENSURE THAT THE MAINS IS

DISCONNECTED BEFORE CARRYING OUT ANY MAINTENANCE, CALIBRATION,

CHECKS, OR ADJUSTMENTS.

CAUTIONS

THE AT-2 CONTAINS STATIC SENSITIVE CMOS COMPONENTS; OBSERVE

ANTISTATIC PRECAUTIONS. WHEN CARRYING OUT ANY MAINTENANCE

PROCEDURES ALWAYS PLACE THE UNIT ON AN EARTHED ANTISTATIC MAT.

PERSONNEL MUST BE EARTHED WHEN HANDLING ANY BOARDS OR

COMPONENTS. ALWAYS USE AN ANTISTATIC BAG WHEN TRANSPORTING

BOARDS OR COMPONENTS

CARE MUST BE TAKEN WHEN REMOVING AND REPLACING CONNECTORS. NEVER

USE FORCE. NEVER STRAIN THE CABLE ASSEMBLIES.

THE PROCEDURAL STEPS GIVEN FOR EACH MODULE MUST BE FOLLOWED IN THE

ORDER GIVEN.

THE OUTER SURFACES OF THE AT-2 ARE SUSCEPTIBLE TO ABRASION DAMAGE.

TO PREVENT SCRATCHING, ALWAYS PLACE ON A SOFT, NON-ABRASIVE CLOTH.

Conditions

The unit must be placed on an antistatic mat and antistatic precautions observed when any

maintenance is carried out on the AT-2.
The room temperature should be between 18 and 28 degrees.

Note:

When a key operation or menu selection is required in the following procedures, the

key sequence required is given in bold letters. The character, or character string,

given is the actual character, or character string, printed on the key.

Summary of Contents for CARDIOVIT AT-2














































































































Search results

Summary of Contents for CARDIOVIT AT-2

Reviews:

Brands by name

Popular brands

Schiller CARDIOVIT AT-2, Service Handbook

Search results

Summary of Contents for CARDIOVIT AT-2

Reviews:

Brands by name

Popular brands