manualshive.com logo in svg

Schiller CARDIOVIT AT-2, Service Handbook

Share
Download
Schiller CARDIOVIT AT-2 Service Handbook Download Page 44

Page 3.4

SCHILLER AT-2 6-Channel ECG Unit

SERVICE HANDBOOK  Issue  2.1  November 1998

Chapter 3

Fault Diagnosis

General Check Procedures

The procedure detailed here is a general confidence check of the unit after an internal module or

board has been replaced. It is not a full functional test (which can only be carried out with dedicated

equipment in the factory) but is intended to provide a general confidence check in all the major

AT-2plus functional areas. The instructions given here are guides to the basic functions. If more

operating information is required (general settings, comprehensive menu guides etc.) please refer

to Chapter 1 in this publication or the relevant User Manual.

To carry out the general AT-2 functional check procedure, proceed as follows:
1. Connect mains power to the unit and ensure that the green mains LED lights.

2. Switch the unit on by pressing the 

 key on the keyboard. Ensure that the LED lights

flash for about a second.

3. Carry out the printer check detailed on the next page.

4. Connect an ECG simulator to the ECG connector on the side panel and switch on.

5. Press the 

 key and ensure that six leads are printed and are of good quality.

6. Press the 

 key and wait approximately 10 seconds for the printout to commence.

Ensure that the printout is accurate and of good quality.

7. Switch the unit off 

 and leave connected to the mains supply for 10 hours or more to

charge the battery.

8. Disconnect the mains and switch the unit on. Ensure that the Battery LED is lit. Run the

unit on battery power for approximately an hour. Ensure that the battery LED flashes when

the battery has limited capacity (not before 6 hours).

Summary of Contents for CARDIOVIT AT-2














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands