background image

5

SAFETY PRECAUTIONS

TRAINING

1. 

Regard the unit as a piece of power 
equipment and teach this regard to all who 
operate this unit.

2. 

Read the instructions carefully. Be familiar 
with the controls and the proper use of the 
equipment.

3. 

Never allow children, teenagers or people 
unfamiliar with these instructions to use this 
piece of equipment.

4. 

Avoid operating unit while people, especially 
children or pets, are nearby.  
Keep in mind that the operator or user  
is responsible for accidents or hazards 
occurring to other people or their property.

5. 

Be sure you know how to stop the  
TRS-20E/TSS-20E at a moment’s notice.

6. 

When using the TRS-20E/TSS-20E, make 
certain frame plate is attached at all times 
when not bagging.

PREPARATION SAFETY

1. 

The use of personal protective equipment, such 
as (but not limited to) protection for the eyes, 
ears, feet and head is recommended.

2. 

While operating, always wear substantial 
foot wear and long trousers. Do not operate 
the equipment when barefoot or wearing 
open sandals.

3. 

Area should be free of all obstacles  
and debris.

ENGINE SAFETY

1. 

Handle gasoline with care; it is highly 
flammable.

2. 

Use an approved gasoline container.

3. 

Always add fuel before starting the engine.

4. 

Fill the fuel tank outdoors.

5. 

If fuel is spilled, do not attempt to start the 
engine. Move away from the area of the spill 
and avoid creating any source of ignition until 
fuel vapors have dissipated.

OPERATIONAL SAFETY

1. 

Carefully read and follow all  
caution stickers.

2. 

Operate only in daylight or good  
artificial light.

3. 

Do not operate machine unless all guards, 
shields and covers are in place and in proper 
working condition.

4. 

It is essential all operator safety mechanisms 
be connected and in operating condition prior 
to use.

5. 

Do not change the engine governor settings 
or over-speed the engine. Operating an 
engine at excessive speed may increase the 
hazard of personal injury.

6. 

Disengage all blade and drive clutches 
(release bail) before starting.

7. 

Start the engine carefully with feet well 
away from the blades.

8. 

Do not put hands, feet or clothing near 
rotating parts while the unit is being 
operated.

9. 

Travel up and down slopes at a 45° angle 
rather than across, to prevent unit from 
tipping over.

10.  Exercise extreme caution when changing 

direction on slopes. Do not get too close  
to sharp drop-offs or operate unit on 
excessively steep slopes.

11.  Use caution when backing up or pulling the 

unit towards you.

12.   Stop the blades if unit has to be tilted for 

transportation, when crossing surfaces (i.e. 
sidewalks, driveways, stepping stones, etc.) 
or when transporting the unit to and from the 
area being worked on.

13.  Never pick up or carry a TRS-20/TSS-20 

while the engine is running.

WARNING

DO NOT

 FILL TANK COMPLETELY FULL.

DO NOT

 SMOKE WHILE YOU FILL FUEL TANK.

DO NOT

 REMOVE GAS CAP IF ENGINE 

 

IS RUNNING.

DO NOT

 OPERATE ENGINE IN A 

 

CONFINED SPACE WHERE DANGEROUS 

 

CARBON MONOXIDE FUMES CAN COLLECT.

Summary of Contents for Classen TRS-20BE


















Reviews: