Schiller Grounds Care Bob-Cat 942311F Operator'S Manual Download Page 38

Page: 38 / 70

FastCat RZ

BELT REPLACEMENT

HYDRO TRANSAXLE DRIVE BELT

1. Remove cutterdeck belt (see cutterdeck belt

replacement).

2. Disconnect wire

at clutch

. Remove bolts

and remove torque restraint.

3. Using a ratchet with a 9/16" socket, place over

nut at location

. Use the ratchet to rotate it

enough to remove the transaxle drive belt.

4. Install a new transaxle drive belt by performing

these steps in reverse order.

5. Inspect the fans. Replace if worn or damaged.

Torque transaxle pulley nut to 28.3-41.6 ft-lbs
(38-56 Nm).

6. Reinstall cutterdeck belt (see cutterdeck belt

replacement).

NOTE:

Always use Schiller Grounds Care, Inc. replacement belts, not general purpose

belts. Schiller Grounds Care, Inc. belts are specially designed for use on this mower and
will normally last longer.

CUTTERDECK BELT

1. Remove floorplate.

2. Set the cutterdeck in a middle height-of-cut posi-

tion.

3. Use a 3/8" ratchet and extension to back

tensioning idler off to remove belt from idler.
Remove belt from cutterdeck pulleys.

NOTE:

Use the 3/8" ratchet in the square hole

the idler.

4. Remove belt from clutch pulley.

5. Install the new belt by performing these steps in

reverse order.

BELT TENSION

All belts are tensioned by spring loaded idlers and do

not require any adjustment.

2 SPINDLE DECK

3 SPINDLE DECK

Summary of Contents for Bob-Cat 942311F







































































Search results

Summary of Contents for Bob-Cat 942311F

Reviews:

Related manuals for Bob-Cat 942311F

Brands by name

Popular brands

Schiller Grounds Care Bob-Cat 942311F, Operator'S Manual

Search results

Summary of Contents for Bob-Cat 942311F

Reviews:

Related manuals for Bob-Cat 942311F

Brands by name

Popular brands