Schiller Grounds Care Bob-Cat 942311F Operator'S Manual Download Page 36 | Manualshive

Page: 36 / 70

background image

34

FastCat RZ

HYDROSTATIC TRANSAXLE ADJUST-
MENTS

A turnbuckle style hydrostat neutral adjustment is
provided.

Neutral:

1. Support the machine with the rear wheels off

the ground. Use jackstands or equivalent sup-
port. Do not rely only on mechanical or hydraulic
jacks.

2. Move the traction levers out into the neutral lock

position and raise the seat.

3. Disconnect the seat switch wire and temporarily

connect the two terminals with jumper wire

J

as

shown.

4. Start the engine and run at low speed.
5. Move parking brake to the

OFF

position.

6. Loosen jam nuts

K

at both ends of the control

rod

L

.

7. Rotate the control rod until the corresponding

wheel stops turning. Lock the control rod jam
nuts. Run the engine up to high idle and stroke
the traction levers forward and back to check the
adjustment. Move traction levers back to neutral
and readjust if necessary.

8. Repeat steps 6 and 7 for the opposite side.
9. Remove the jumper wire and reconnect the seat

switch.

ADJUSTMENTS

«
...
34
35
36
37
38
...
»

Summary of Contents for Bob-Cat 942311F







































































Reviews:

No comments

Related manuals for Bob-Cat 942311F

Brand: Viking Pages: 56

Brand: Rally Pages: 28

Brand: Yard Machines Pages: 12

Brand: Matrix Pages: 96

Brand: Poulan Pro Pages: 48

Brand: Toro Pages: 28

Zero Turn Radius Mower

Brand: Country Clipper Pages: 25

Brand: Yardworks Pages: 24

Brand: MTD Pages: 28

TH910 Series II

Brand: Deutscher Pages: 22

Brand: Walker Rider Lawnmowers Pages: 100

Brand: Jacobsen Pages: 92

Brand: MTD Pages: 32

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 64

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands