Schiller Grounds Care 942514K Operator'S Manual Download Page 39

Page: 39 / 42

PREDATOR-PRO

SERIES

POWER UNITS

ENGINES:

Construction:

Aluminum block with cast-in cast iron

sleeves. Aluminum head.

Configuration:

4-stroke, vertical shaft, V-twin cylin-

der, overhead valve, air-cooled.

DRIVE SYSTEM:

Full hydrostatic pump and wheel motor combination

for independently controlled drive wheels.

Pump:

Hydrogear 16cc variable displacement piston

pump.

Motors:

Parker displacement MB series. Direct

drive 1-1/4” (31.8mm) diameter output shaft.

Turn Radius:

True Zero

OPERATOR PRESENCE

INTERLOCK SYSTEM:

Start:

The PTO (blades) must be off, traction levers

in neutral lock, and parking brake on for engine to

crank.

Run:

Operator must be in seat to take parking brake

off, to move traction levers out of the neutral lock

position, or to turn the PTO (blades) on or the engine

will kill. The parking brake must be off for the traction

levers to move out of the neutral lock position.
The operator may leave the seat with the engine

running if the parking brake is on, the PTO (blades)

is off, and the traction levers are in the neutral lock

position. A time delay eliminates annoying engine

cutout from operation over rough terrain.

WEIGHT:

1256 lbs (570 kg) w/52" deck

1293 lbs (587 kg) w/61" deck

1404 lbs (638 kg) w/72" deck

CONTROLS:

Throttle; choke; power takeoff (PTO) clutch switch;

traction levers; parking brake lever; lift lever.

FUEL SYSTEM:

One tank on each side of operator. Total capacity 14

gallons (52.9 liters). Fuel selector/shutoff switch on

rear cooler mounting bracket(1/4 turn). Replaceable

fuel filter.

MAXIMUM GROUND SPEEDS:

Forward:

12.5 mph (20.1 km/h)

Reverse:

4 mph (6.4 km/h)

WHEELS & TIRES:

Drive wheels:

942529K

23 X 10.5-12 4-Ply Turf

Tread

Tires

942514K, 942515K

24 X 12.00-12 4-Ply Turf

942516K, 942519K

Tread Tires

Casters:

13 X 6.5-6 No-Flat tires

Pressure:

12 p.s.i.

BRAKING:

Parker brakes. Spring applied for overload

protection.

SEAT:

High back, foam padded full suspension seat with

standard armrests. Fore and aft adjusters, hinged for

easy tilt-up access to pumps and battery. Internally

mounted seat switch.

SPECIFICATIONS

Summary of Contents for 942514K











































Search results

Summary of Contents for 942514K

Reviews:

Related manuals for 942514K

Brands by name

Popular brands

Schiller Grounds Care 942514K, Operator'S Manual

Search results

Summary of Contents for 942514K

Reviews:

Related manuals for 942514K

Brands by name

Popular brands