automatic cable rewinder FT 260/350 - EFT 265 MFK
installation and operating instruction
installation and operating instruction FT 260_350-EFT 265 MFK - A5
page 4
01.04.2021
Schill GmbH & Co. KG; Bruckstraße 44; 70734 Fellbach
FT 350
Starting from a standard spring, with a maximum of 29
revolutions, the following pull-out and connection lengths are possible.
cable OD [mm]
pull-out length [m]
connection length [m]
≤ 8
17
1,5
≤ 10
18
1,2
≤ 12
20
0,9
The maximum spring force is 55N
(5.5kg).
The values specified in the tables are approximate values. If you have any questions, please contact the manufacturer directly (see
"CONTACT").
CABLE INSTALLATION
•
Loosen all the screws and remove the cover ccarefully.
Attention
The spiral spring in the coil is under tension. Please ensure that the locking mechanism is activated.
•
Take the tension off the coil. To do this, proceed as follows:
➢
Carefully turn the coil against the clockwise direction until the rattling of the ratchet is no longer heard. A pull will be
noticeable. Do not let go of the coil.
➢
Slowly run back the coil. The coil should be easily movable at the end and not locked in the locking.
•
Dismantle strain relief and screws in the coil.
•
Guide the cable through the opening in the coil until connection length X.
•
Fix the cable with the strain relief.
•
Store the overstanding connecting cable inside the coil and securely with the Velcro fastener.
•
Install the cable stopper at the end of the pull-out cable.
•
Wind the pull-out cable counterclockwise on the coil.
•
Adjust the pre-load:
Hold the stopper outside the housing and hold it with one hand. Now turn the coil as often as you want to pre-load. At the end let it
snap into the notches (see "LOCKING DEVICE").
•
Undertake the re-assembly in reverse order
(see “TIGHTENING TORQUE”).
•
After the complete re-assembly undo the locking. Pull on the cable stopper, wind out the cable complete and slowly rewind it.
•
Before re-mounting at the operation area, please check for a correct performance.
TECHNICAL DATA
Our cable reels with their robust design are made for operating in factories and workshops. The sturdy plastic design, made from high-
quality materials, is completely electrically insulated, corrosion resistant and has very good winding characteristics. The cable reels come
as a standard without cable.
•
Spiral spring for approx. 30. 000 operations
•
Locking by reliable spring rest (only switch-off with FT version)
•
Without slip ring / rotary join
•
Without thermal safety guards
•
Cable assembly
cable outer diameter[mm]
FT260/EFT265 pull-out length
FT 350 pull-out length
connection length
≤ 8
10m
17m
1,5m
≤ 10
8m
18m
1,2m
≤ 12
6m
20m
0,9m
•
Cable stopper with segmented gentle clamp 6
– 12mm / 6 – 16mm
•
Bracket / Fixing:
➢
FT 260 Universal holder for wall or ceiling mounting
➢
FT 350 serial holder for wall mounting (optional ceiling holder)
➢
EFT 265 mounting holes 4 x Ø=6mm
•
Ambient temperature range -25°C to 40°C
The specified range of ambient temperature applies only to the reels and not to the cable assembly or connectors. These are only part of
the delivery in exceptional cases. Specifications for plug-in connections can be found under the standard DIN EN 60390.
The dimensions, weights, lengths, coloures and traction are subject to modifications.
We cannot rule out discrepancies and we reserve the
right to make technical changes to the product without giving advance notice.