schildknecht DATAEAGLE X-treme IO 2730 Installation And Commissioning Manual Download | Manualshive

Page: 31 / 32

background image

Installation and commissioning SET DATAEAGLE X-treme IO 2730

LED indicator

Distance

Antennas

Sources of
interference

Kapitel 6 – Tipps und Tricks

6.3. Advices for troubleshooting

Check the display of the status LEDs

Check the distance towards the partner station. Select first a
distance of a few meters and increase the distance step by
step up to the intended distance.

Check the antenna connection. Check if all antennas are
connected correctly. Pay attention that coax antenna cable is
not flexed. Check next if all antennas are installed according
to the guidelines described in chapter 6.2.

Check if there are any interferences on the transmission
side.

«
...
29
30
31
32
»

Summary of Contents for DATAEAGLE X-treme IO 2730

































Reviews:

No comments

Related manuals for DATAEAGLE X-treme IO 2730

Passport 500 Pro

Brand: Fender Pages: 4

Brand: Sennheiser Pages: 6

Brand: Zhong Shan Anders Electronics Pages: 5

C 1000 S - PPC 1000 & PB 1000

Brand: AKG Pages: 14

Brand: Comica Pages: 28

Brand: Retekess Pages: 4

VoiceLift Pro VLS 3001

Brand: Extron electronics Pages: 41

Brand: CARVIN Pages: 4

Brand: Technics Pages: 60

Brand: Technics Pages: 79

Brand: Trivum Pages: 12

Brand: Curtis Pages: 1

Brand: Curtis Pages: 4

Brand: Curtis Pages: 7

Brand: Curtis Pages: 17

Brand: Sennheiser Pages: 2

Brand: OK. Pages: 11

Brand: Vitek Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands