manualshive.com logo in svg

SCHIEBEL ACTUSAFE CMFS, Operating Manual, Page: 63 / 99

Share
Download
SCHIEBEL ACTUSAFE CMFS Operating Manual Download Page 63

Operating Manual Linear ACTUSAFE CMFS(L)
OM-ENGLISH-Failsafe-Linear-16xx-V2.00-2022.03.03

7 Parameter menu

7.15

Parameter group: Characteristic curves (optional)

With this option, customers can enable travel-dependent torque, speed and valve characteristic curves.

7.15.1

Torque characteristic

With this characteristic curve, torque limits already set under menu item

P2-torque

(see section 7.2, page 43) can be

further

reduced

depending on travel. Characteristics can be configured via the SMARTTOOL software (see Figure 71,

page 61).

Figure 71:

Torque characteristic

Menu item

Sub-menu item

poss. setting

Notes / comments

P17.1

Characteristic

Torque Open

0: Off

The torque characteristic curve is disabled for the OPEN

direction.

1: On

The torque characteristic curve is enabled for the OPEN

direction.

2: Local + Remote

only

The torque characteristic curve is enabled for the OPEN

direction only in LOCAL and REMOTE mode (while

disabled in the EMERGENCY mode).

P17.2

Characteristic

Torque Closed

0: Off

The torque characteristic curve is disabled for the

CLOSED direction.

1: On

The torque characteristic curve is enabled for the

CLOSED direction.

2: Local + Remote

only

The torque characteristic curve is enabled for the

CLOSED direction only in LOCAL and REMOTE mode

(while disabled in the EMERGENCY mode).

63

Summary of Contents for ACTUSAFE CMFS




































































































Reviews:

No comments