manualshive.com logo in svg

SCHIEBEL ACTUSAFE CMFS, Operating Manual, Page: 54 / 99

Share
Download
SCHIEBEL ACTUSAFE CMFS Operating Manual Download Page 54

7 Parameter menu

Operating Manual Linear ACTUSAFE CMFS(L)

OM-ENGLISH-Failsafe-Linear-16xx-V2.00-2022.03.03

continued from previous page

Menu item

Sub-menu item

poss. setting

Notes / comments

34: Torque Closed

Masked

As Torque CLOSED, but it will supress (mask) this signal

in the end position upon torque-dependent switch-off.

35:Ready Remote

Ready and Remote operating mode

36: Ready Local

Ready and Local operating mode

37: Ready

Local/remote

Ready and Local or Remote mode

38: Emerg. Open

Locked

Lock OPEN is enabled. OPEN command is internally

queued with the highest priority and will not be dropped

even in the end position.

39: Emerg. Closed

Locked

Lock CLOSED is enabled. CLOSED command is

internally queued with the highest priority and will not be

dropped even in the end position.

40: Failsafe OK1

Failsafe OK (only for Failsafe actuators)

41: Failsafe OK2

Failsafe OK and Ready (only for Failsafe actuators)

42: Failsafe OK3

Failsafe OK,Ready and Remote (only for Failsafe

actuators)

43: Emerg. Locked

Lock Open or Lock Closed is enabled.

44:

Ready/TorqueOK

Actuator is ready and no torque switch-off

45: Ready /

Remote /

TorqueOK

Actuator is ready for operation in REMOTE mode and no

torque switch-off

46: Pos.=Int1

Position = Intermediate position 1. The width of the

interval is set with the parameter P8.6.

47: Pos.=Int2

Position = Intermediate position 2. The width of the

interval is set in parameter P8.6.

48: Pos.=Int3

Position = Intermediate position 3. The width of the

interval is set in parameter P8.6.

49: Pos.=Int4

Position = Intermediate position 4. The width of the

interval is set in parameter P8.6.

50:

Pos.=EmergPos

Position = emergency position. The width of the interval

is set in parameter P8.6.

51: Bus Bit 1

In existing bus interface (hardware option), the output is

set according to the selected bit bus.

52: Bus Bit 2

53: Bus Bit 3

54: Bus Bit 4

55: Bus Bit 5

56: Bus Bit 6

57: Bus Bit 7

58: Bus Bit 8

59: Virtual 1

Configurable output function

60: Virtual 2

61: Virtual 3

62: Virtual 4

63: Control OK

The SMARTCON control is operational.

64: Control voltage

OK

The auxiliary voltage for the SMARTCON control is OK.

This function is only available if the auxiliary voltage

output is not switched on (P6.5 to 0).

65: PVST OK

The PVST was successful.

66: PVST Failure

The PVST was not successful.

67: PVST Active

A PVST was triggered. The actuator is running a PVST.

68: Emerg. OPEN

Emergency OPEN command is active. The signal

remains active, as long as the emergency command is

active, even if the end limit is reached.

69: Emerg.

CLOSE

Emergency CLOSE command is active. The signal

remains active, as long as the emergency command is

active, even if the end limit is reached.

continued on next page

54

Summary of Contents for ACTUSAFE CMFS




































































































Reviews:

No comments