background image

WARNINGS

PRECAUTIONS

WARNINGS

Read carefully this manual and follow these 

precautions before operating the device

Keep this manual for possible future needs

Pay attention not to pour liquids onto the device and do not operate in conditions of excessive humidity

Do not install the device close to sources of excessive heat, do not expose it to direct solar radiation and do not 

position it without protection in a dusty environment

Be sure that the main voltage does not exceed the value indicated on the back panel

Do not use the device if the main cable or the plug aren’t in a perfect condition (if necessary, replace it)

If the main cable has to be replaced, the operation must be carried out by qualified personnel. Replace the cable 

exclusively with one that is an exact substitute

In order to avoid interference, do not install the device close to power transformers, TV sets, RF transmitters, electric 

motors or any source of electric energy

Do not point microphones against speakers: this could generate annoying whistles (Larsen effect) that cause damage

In order to avoid unpleasant and costly inconveniences, use only original connecting cables

To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC socket

When cleaning, do not use solvents (e.g. acetone or alcohol). These could damage the external finishing and the 

serigraphy

Do not attempt to service this product. In case of malfunction of any part of the system call the nearest technical 

assistance centre or a specialized technical centre

For good ventilation, the heat sink should never be covered or obstructed by blankets, sofas or similar furniture. Be 

sure also to leave sufficient clearance between the heat sink and any other surface

No source of flames, e.g. candles, should be placed on or near the device

The device should not be exposed to water, even in small amounts. No object containing liquids should be placed on 

or near the device

The device should only be connected to a mains socket outlet equipped with protection ground system

When the device is installed, be sure the mains socket and the plug of the mains cable are easily accessible

Summary of Contents for TEDDY









Reviews: