www.scheppach.com
34 | GB
12.2.2 Carbon brushes
In case of excessive sparking, have the carbon brush-
es checked only by a qualified electrician.
IMPORTANT
The carbon brushes should not be replaced by anyone
but a qualified electrician.
12.2.3 Mains cable
If the mains cable is pulled out, cut, or damaged in
some other form, then it should be replaced immedi-
ately.
12.2.4 Replacing the fine-wire fuse (fig. 16)
If the fine-wire fuse (36) is defective, it must be re
-
placed with a fine-wire fuse of the same type.
WARNING
Do not bypass the fine-wire fuse (36)! Do not use fus
-
es of any other type! This can lead to damage to the
device.
12.3 Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: Carbon brushes, saw blade, table inlay
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.
12.4 Ordering replacement parts
The following information must be provided on all or-
ders for spare parts:
• Device type
• Device article number
13. Storage
Store the equipment and accessories out of children’s
reach in a dark and dry place at above freezing temper-
ature. The ideal storage temperature is between 5 and
30 °C. Store the electric tool in its original packaging.
11. Transport
• Transport the electric tool by lifting it on the recesses
provided for this on the frame and the engine cover.
• Never use the protective devices for handling or
transport.
• Make sure that the exposed part of the saw blade
is covered during transport, e. g. by the protective
device.
12. Cleaning, maintenance, storage
and ordering of spare parts
WARNING
Always switch the machine off and remove the mains
plug prior to all maintenance and cleaning work.
12.1 Cleaning
Keep all safety devices, air vents and the motor hous-
ing free of dirt and dust as far as possible. We recom-
mend that you clean the equipment immediately after
you use it.
12.1.1 Exterior cleaning
• Clean the equipment regularly with a damp cloth and
some soft soap.
• Do not use cleaning agents or solvents; these may
be aggressive to the plastic parts in the equipment.
• Ensure that no water can get into the interior of the
equipment.
12.1.2 Interior cleaning (fig. 15)
1. Open the storage box (9).
2. Remove the screw (35).
3. Loosen the screw (34).
4. Remove the cover (8).
5. Blow out the device interior with low-pressure
compressed air.
6. Attach the cover again (8).
7. Fasten the screw (34).
8. Insert the screw (35) again and tighten it.
9. Close the storage box (9).
12.2 Servicing
12.2.1 Bearings (fig. 1/pos. 10)
Lubricate the bearing points (10) of the deflection roll
-
ers after approx. 25-30 operating hours at the latest
using high-quality machine grease.
Summary of Contents for 5901407901
