background image

 

 
Bandwidth Chart: 

The bandwidth will be varied based on different resolution.    Higher resolution may not request 
bigger bandwidth. Below Chart is the resolution and bandwidth status for reference.   
 

Resolution (@60Hz) 

Average Bandwidth (Mbps) 

1080p 

77 (24 ~ 91) 

720p 

46 (29 ~ 150) 

480p 

63 (36 ~ 73) 

1600x1200 (UXGA) 

59 (24 ~ 73) 

1280x1024 (SXGA) 

58 (31 ~ 76) 

1024x768 (XGA) 

118 (56 ~ 138) 

800x600 (SVGA) 

83 (64 ~ 107) 

 
Under Gigabit Ethernet network, the total flow must not exceed 1000Mbps to avoid any delay on 
video streaming.    If the video play with 1080p resolution, the HE05BT Transmitter allow maximum 
up to 10pcs for simultaneous video streaming. 

 
Remote Control Function: 

 

If you do not use PC computer management to setup HE05BR, then you could use 
the IR infrared remote control to preset channel selection.      Using the IR remote 
control to the front of HE05BR will be ok. 

 
Initial at first time use the remote control or after change battery of remote control, 
the IR remote control and the equipment IR ID must be using same ID.    The default 
IR ID is 8.   
 
To setting the IR ID, Press and hold power button, then press button 8 to complete 

the setting. 

    + 

.(for example)   

 

 

 

Remote Control Button Function:   

Symbol                                          Function 

  

Power 

 

 

 

Temporarily turn off the screen output /setup remote control IR ID 

  

MENU 

 

 

 

Quick menu selection, input numbers after press menu button 

  

LEFT 

 

 

 

previous channel 

  

RIGHT 

 

 

 

next channel 

  

UP   

 

 

 

previous quick Menu selection 

  

DOWN 

 

 

 

next quick Menu selection 

  

ENTER   

 

       

Confirmation / display the current channel 

  

 

 

         

number 1 

  

 

 

 

 

number 2 

  

 

 

 

 

number 3 

  

 

 

 

 

numuber4 

Summary of Contents for HE05BR


















Reviews: