Ventilation condition
The position you select for the freezer installation should be well-ventilated and
has less hot air. Do not locate the freezer near a heat source such as cooker, and
avoid it from direct sunlight, thus guaranteeing the refrigeration effect while sav-
ing energy consumption. Do not locate the freezer in the damp place, so as to
prevent the freezer from rusting and leaking electricity. The result of the total
space of the room in which the freezer is installed being divided by the refrigerant
charge amount of the freezer shall not be less than 8 g/ M3.
Note:
The amount of refrigerant charged for the freezer can be found on the
nameplate.
Heat dissipation space
When working, the freezer gives off heat to surroundings. Therefore, at least 30
mm of free space should be spared at the top side, more than 100 mm on both
sides, and above 50 mm at the back side of the freezer.
W
D
H
A
B
C(
°
)
E
F
912
704
1770
1524 1062
160
50
100
Level ground
Place the freezer on the solid and flat ground (floor) to keep it stable, or else, it will
give rise to vibration and noise. When the freezer is placed on such flooring mate-
rials as carpet, straw mat, polyvinyl chloride, the solid backing plates should be
applied underneath the freezer, so as to prevent color change due to heat dissi-
pation.
Unobstructed ventilation shall be maintained around the appliance or in an em-
bedded structure.
Preparations for use
Standing time
After the freezer is properly installed and well cleaned, do not switch it on imme-
diately. Make sure to energize the freezer after more than 1 hour’s standing, so
as to ensure its normal operation.
Cleaning
Confirm the accessory parts inside the freezer and wipe the inside with a soft
cloth.
Power-on
Insert the plug into the solid socket to start the compressor. After 1 hour, open
the freezer door, if the temperature inside the freezer compartment drops obvi-
ously, it indicates the refrigeration system is working normally.
Storage of food
After the freezer runs for a period of time, the internal temperature of the freezer
will be automatically controlled according to the user’s temperature setting. After
the freezer is fully cooled, put in foods, which usually need 2-3 hours to be fully
cooled. In summer, when the temperature is high, it takes more than 4 hours for
the foods to be fully cooled (Try to open the freezer door as less as possible before
the internal temperature cools down).
If the freezer is installed in the moisture place, make sure to check whether the
ground wire and leakage circuit breaker are normal. If vibration noises are pro-
duced due to the freezer contacting the wall or if the wall gets blackened by air
convection around the compressor, move the freezer away from the wall. Setting
up the freezer may cause jamming noise or image chaos to the mobile phone,
fixed-line telephone, radio receiver, television surrounding it, so try to keep the
freezer as far away as possible in such case.
Functions
The display panel is designed on the fridge door, illustrated as the figures below:
1 Freezer zone
2 smart icon
3 inverter icon
4 fast freeze icon
5 Temp zone button
6 function button
7 unlock button
8 fridge zone
9 digital temperature display
10 temp button
11 OK button
Function Setting
When the refrigerator system is connected to power supply for the first time, all
icons on the display panel gets illuminated for 2s, and the system runs in the Smart
mode by default. When all the doors are close, the display gets extinguished au-
tomatically if no key operation within 3 minutes. When the display is off, it will
light up if any door is opened or any key is pressed.
The following key operations are valid only when the keys are unlocked and gets
illuminated on the display.
“Inverter” is the frequency conversion indicator. When the power is turned on, it
lights up when the compressor is working.
Fridge temperature setting
Press the Temp. Zone key to select the fridge zone until the corresponding icon
gets flickering, and then press the Temp. key to set the temperature as desired,
finally, press the OK key to validate the setting.
The fridge temperature setting cycles as following:
5
℃
→6
℃
→7
℃
→8
℃
→OF→2
℃
→3
℃
→4
℃
→5
℃
OF indicates the fridge is switched off, and when the OF function takes effect, the
fridge will stop cooling.
Be sure to take all foods out of the fridge compartment before setting this func-
tion.
Freezer temperature setting
Press the Temp. Zone key to select the freezer zone until the corresponding icon
gets flickering, and then press the Temp. key to set the temperature as desire,
finally press the OK key to validate the setting.
The freezer temperature setting cycles as following:
-18
℃
→-17
℃
→-16
℃
→-24
℃
→-23
℃
→-22
℃
→-21
℃
→-20
℃
→-19
℃
→-18
℃
Fast Freeze
1)When the Fast Freeze function is enabled, the freezer temperature will be con-
trolled at -32
℃
automatically, and after 26 hours of running, the Fast Freeze func-
tion gets exited. Cooling down the freezer temperature in a rapid manner is ben-
eficial to the prevention of food nutrition against lost and the preservation of
freshness.
Under the Fast-Freezing mode, the freezer temperature is subjected to no adjust-
ment.
Enabling the Fast-Freezing function
Press the Function key to select Fast Freeze until the corresponding icon gets flick-
ering, and then press the OK key within 5s for confirmation. If the OK key is not
pressed within 5s, the setting will be invalidated.
