WARNING:
➢
For safety reason, please use only
the same size of fixing or mounting
screws which are recommended in
this instruction manual.
➢
Failure to install the screws or fix-
ing device in accordance with
these instructions may result in
electrical hazards.
Start Using Your Cooker Hood
Touch control with LED display
LED touch control has five buttons, see picture.
(Decrease),
(Increase),
(Lamp),
(Timer),
(Power)
1.
Power-on: After connecting the cooker hood to the main supply,
the backlight of button will turn on, output will be closed and the
cooker hood will enter into stand-by mode.
2.
“
POWER
”
button:
2.1 Press
“
P
OWER”
button, the backlight of button will be on and the
hood will work at the low speed, and the light will be on. The
backlight of the buttons
“
D
ECREASE”
,
“
I
NCREASE”
,
“LAMP”
, and
“
P
OWER”
will be on. Press
“POWER”
button again, the backlight of
button will be off and the cooker hood will be turn off and return
into stand-by mode and operate by the circle.
2.2 . The button of
“LAMP”
button could be operated without pressing
the
“POWER”
button. Press
“POWER”
button, the cooker hood will
be turn off without any functions.
2.3
“LAMP”
button:
Press
“LAMP”
button, the backlight of button and the lights will be on.
Press again, the lights will be off. The lights run circularly.
3.
“
I
NCREASE”
button:
3.1 Press
“INCREASE”
button, the backlight of button will be on, the
cooker hood starts to work at the low speed. the LED display will
display “1”,
3.2 Press
“INCREASE”
button again when it is working on the low speed,
the cooker hood works at the mid speed and the LED display will
display “2”,
3.3 Press
“INCREASE”
button again when it is working on the mid speed,
the cooker hood works at the high speed and the LED display will
display “3”.
4.
Press
“DECREASE”
button
4.1 Press
“DECREASE”
button, the cooker hood will decrease one
speed, and the display will show the current working speed. When
press
“DECREASE”
button again when it is working on the low
speed, the cooker hood will turn off and the backlight of the
“DECREASE”
button will be off.
5.
Press
“TIMER”
button:
5.1 The
“
T
IMER”
button works when the motor and light is on only.
The timer setting is 5mins and could be repeat setting. When the
time is up, the cooker hood will be turn off and the light will be off.
5.2 When the timer is set, if adjusting the speeds, the timer will re-
calculate the working time.
Troubleshooting
Fault
Possible Cause
Solution
Light on, but motor
does not work
Fan switch turned
off
Select a fan
switch posi-
tion.
Fan switch failed
Contact ser-
vice center.
Motor failed
Contact ser-
vice center.
Light does not work,
motor does not work
House
fuses
blown
Reset/Re-
place fuses.
Mains power ca-
ble is loose or dis-
connected
Refit mains
power cable
to
power
outlet.
Switch
power out-
let on.
Oil leakage
One way valve
and the outlet are
not tightly sealed
Take down
the one way
valve
and
seal
with
sealant.
Leakage from the
connection
of
chimney
and
cover
Take chim-
ney
down
and seal.
Lights not working
Broken or faulty
bulbs
Replace
bulbs as per
this
instruction.
Insufficient suction
The distance be-
tween the cooker
hood and the gas
top is too far
Refit
the
cooker hood
to the cor-
rect
dis-
tance.
The Cooker hood in-
cline
The fixing screw is
not tight enough
Tighten the
hanging
screw and
make it ho-
rixontal
NOTE:
Any electrical repairs to this appliance must conform to
your local, state and federal laws. Please contact the service
centre if in any doubt before undertaking any of the above.
Always disconnect the unit from the power source when opening the
unit.
