3
P
R
O
P
E
R
L
Y
P
R
O
P
E
R
L
Y
P
R
O
P
E
R
L
Y
P
R
O
P
E
R
L
Y
P
R
O
P
E
R
L
Y
S
E
R
V
I
C
E
S
E
R
V
I
C
E
S
E
R
V
I
C
E
S
E
R
V
I
C
E
S
E
R
V
I
C
E
E
N
G
I
N
E
E
N
G
I
N
E
E
N
G
I
N
E
E
N
G
I
N
E
E
N
G
I
N
E
W
I
T
H
W
I
T
H
W
I
T
H
W
I
T
H
W
I
T
H
OIL
OIL
OIL
OIL
OIL
A
N
D
A
N
D
A
N
D
A
N
D
A
N
D
F
U
E
L
.
F
U
E
L
.
F
U
E
L
.
F
U
E
L
.
F
U
E
L
.
3.3 CATCHER FRAME ASSEMBLY
1. On the LH side of the machine remove the two
bolts securing the pump mounting plate to the
machine. Align the holes in the hitch bracket
weldment (item 53) with the holes in the machine
frame. Install (2) 3/8-16 x 1-1/4" bolts into the
rear holes of the frame and the hitch bracket.
Install (2) 3/8-16 x 1" bolts into the front holes.
Secure using four 3/8-16 elastic stop nuts.
-Note-
Install the hitch bracket mounting hardware
from the inside of the machine through the
machine frame and then through the hitch
bracket. This will prevent the hardware from
interfering with the linkage.
2. Repeat step 10 on the RH side of the machine.
3. Install the 1/2-13 nut (item 19) onto the 1/2-13 x
1-1/2" bolt (item 14). Thread the bolt and nut
assembly into the boss on the catcher frame (item
49). Do not tighten at this time.
4. Align the pins on the catcher frame (item 49)
with the hitch brackets. Slide the catcher frame
into the tubes on the hitch brackets and secure
using the quick pins (item 32).
5. Adjust the 1/2-13 nut and bolt assembly, that
was installed onto the catcher frame in step 3 ,
so the head of the bolt rests against the belt cover
on the machine. Tighten the nut against the boss
to secure the bolt from moving.
6. Align the holes in the RH upright post weldment
(item 51) with the holes on the RH side of the
catcher frame. Place (2) 3/8" flat washers onto
(2) 3/8-16 x 3-1/2" bolts and insert the bolts into
the holes of the upright post and the catcher
frame.
7. Install the RH brace (item 36) to the RH upright
post. Secure using (1) 5/16-18 x 2-1/2" bolt, (1)
5/16" flat washer and (1) 5/16-18 elastic stop
nut. Secure the other end of the RH brace to the
catcher frame using (1) 5/16-18 x 1" bolt and (1)
5/16-18 elastic stop nut.
8. Slide the engine support frame (item 54) under
the catcher frame and install onto the bolts that
are inserted into the RH upright post and the
catcher frame. Secure using (2) 3/8-16 elastic
stop nuts and (2) 3/8" flat washers.
9. Install the LH upright support weldment (item
50) to the LH side of the catcher frame. Insert
(2) 3/8-16 x 3-1/2" bolts and (2) 3/8" flatwashers
into the holes of the upright post, the catcher
frame and the engine support frame. Secure
using (2) 3/8-16 elastic stop nuts and (2) 3/8"
flat washers.
10. Install the LH brace (item 35) to the LH upright
post. Secure using (1) 5/16-18 x 2" bolt, (1)
5/16" flat washer and (1) 5/16-18 elastic stop
nut. Secure the other end of the LH brace to the
catcher frame using (1) 5/16-18 x 1" bolt and (1)
5/16-18 elastic stop nut.
11. Install (1) 5/16-18 nut onto the eyebolt (item 34).
Install the eyebolt through the LH upright
support and secure with (1) 5/16-18 elastic stop
nut.
12. Install the heatshield (item 37) to the catcher
frame using (1) 5/16-18 x 3/4" carriage bolt, (1)
5/16" flat washer and (1) 5/16-18 elastic stop
nut.
13. Secure the 2 heatshields to the two upright
supports using (6) 5/16-18 x 3/4" carriage bolts,
(6) 5/16-18 elastic stop nuts. The heatshields
will mount on the outside of the supports and
have an air space between them when installed
properly.
14. Slide the bucket (item 57) onto the catcher frame
and secure using the rubber strap (item 62).
Hook one end of the rubber strap into the washer
welded onto the RH upright support and the
other end into the eyebolt bolted onto the LH
upright support.
