SBC PCD3 Series Page 9 Manual Download

Page: 9 / 133

Saia-Burgess Controls AG

Hardware manual for PCD3 series │ Document 26-789 ENG19│ 2018-06-29

Introduction

Guidance

2-2

2.1 Introduction

Symbols used in this manual for notes, definitions for the serial interfaces,

explanation of terms (glossary) and the company address and address for repairs

are added to the appendix.

You are welcome to submit supplements and suggested improvements to the

following e-mail address

[email protected]

This manual explains the technical aspects of the PCD3 components. The

following terms are commonly used:

CPU

Central processing units: the heart of the Saia PCD

RIOs

Remote I/Os: inputs and outputs that are connected to the CPU

via a fieldbus such as Profibus

LIOs

Local I/Os: these are connected to the CPU or RIO via the I/O

bus (i.e. using very short cables)

Modules

Input/output modules mounted in a housing matched to the PCD3

system

Module

holders

CPU, RIOs or LIOs that can hold modules

The purpose of this chapter is to demonstrate the essentials in the planning and

installation of control systems with PCD3 components.

The following topics are relevant in this regard:

Planning of an application

(chapter 2.4)

I/O module cabling

(chapter 2.5)

Series cabling

(chapter 2.6)

Addressing

(chapter 2.7)

Details about hardware, software, configuration, maintenance, and troubleshooting

are described in separate chapters.

All PCD3 I/O modules are described in the 27-600 Manual I/O Modules

PCD2 and PCD3.

The aforementioned manual and further documentation can be found on our

homepage under documentation or at the respective system groups:

www.sbc-support.com/en/documents/manuals/

Summary of Contents for PCD3 Series






































































































































Search results

Summary of Contents for PCD3 Series

Reviews:

Related manuals for PCD3 Series

Brands by name

Popular brands

SBC PCD3 Series, Manual

Search results

Summary of Contents for PCD3 Series

Reviews:

Related manuals for PCD3 Series

Brands by name

Popular brands