8. The mobile base is now ready for your Professional Cabinet Saw, but before placing the saw on the mobile
base, it is important to rotate the rear hold-down bracket back as far as possible and to rotate the front hold-
down bracket forward as far as possible (see Fig. 8). To safely place the saw into the mobile base, you will
need at least four people to lift the saw off the
floor and then lower it onto the mobile base.
Have one person lift each corner of the cast
iron table top. If your saw has an extension
table, have the two people on the right side
of the saw lift on the extension rails near the
outer corner of the cast iron extension wing,
not at the end of the extension table. If a fifth
person is available, it may be easier to have
four people lift the saw and the fifth person
slide the base under the saw.
Make sure the mobile base is centered
underneath the table saw and that the foot
pedal is in the front. The saw should sit on the
front and rear support straps extending across
the interior of the mobile base, and the front
of the cabinet should be touching the inside of
the front face of the mobile base frame (see
Fig. 8)
.
Never place fingers,
toes or other body
par
ts
under t
he mobile base.
!
WARN
IN
G
1. Never
place
finger
s, toes
or other
body
parts under
the mobi
le base.
2. Always
use
the saw
and
the mobi
le
base
on a level
surface.
3. Do
not conti
nue
to step
on the
foot
pedal
once
the upper
limit is
reached.
4. Lower
the sa
w befor
e use.
Never
use
the saw
when
it is rai
sed
off the
floor.
!
WARN
ING
Raise
Never place fingers,
toes or
other body parts
under the mobile base.
!
WARNING
Low
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARN
ING
5 SawStop Mobile Base Conversion Kit
9. Locate the two self-tapping screws and the two M4 x 12 x 1 washers. Some cabinet configurations will have
pre-drilled holes for the self-tapping screws. If your saw cabinet does not have pre-drilled holes, or you are
having difficulty aligning the holes, rotate the rear hold-down bracket until the top hole is over the flat face of
the cabinet. Place one of the M4 x 12 x 1 washers over the end of one of the self-tapping screws and use a
drill with a
1
⁄
4
inch hex drive bit to mount the rear hold-down bracket to the cabinet, as shown in Fig. 9a. There
is no need to pre-drill a hole for the self-tapping screws, but be careful not to overtighten the screws or the
threads in the cabinet may strip out. Now, rotate the front hold-down bracket until it is vertical and repeat the
same procedure to mount it to the cabinet, as shown in Fig. 9b.
Fig. 9a
Fig. 9b
M4 x 12 x 1
washer
self-tapping
screw
rotate the rear hold-
down bracket until the
top hole is over the flat
face of the cabinet and
then mount it to the cab
-
inet with a washer and a
self-tapping screw
rotate the front
hold-down bracket
until it is vertical
and then mount it
to the cabinet with
a washer and a
self-tapping screw
M4 x 12 x 1
washer
self-tapping
screw
Congratulations
, the assembly is now complete. Please see the Industrial Mobile Base Owner’s Manual for
instructions on how to use and adjust the mobile base and for information on hydraulic jack maintenance.
Assembling Your Mobile Base
Fig. 8
straps that
support the
saw
the front of the
cabinet should be
touching the inside of
the front face of the
mobile base frame
rotate hold-down
bracket back
rotate hold-down
bracket forward
