background image

8

Maintenance

Winterization

Under normal operating conditions this Skimmer will provide years of trouble-free use. Here are a 

few items which will require periodic maintenance:

1.  Check and remove debris captured in the leaf basket every week or as needed. The frequency 

required will vary seasonally, with cleaning required more often in the fall than at other  

times.

Prepare for winterization in mid-to-late November, or when ice persistently develops on the pond. 

Keep equipment winterized until late February or early March when the water temperature rises 

consistently to 40ºF or higher.

If the pond is to be shut down in winter:

1.  Disconnect pump, clean and store in bucket of water. This prevents any rubbers seals from

 

drying and cracking.

2.  Drain any plumbing lines not buried below frost line (18”-24” in agricultural zones 4-6).

3.  Use plumber’s heat tape on pipes and shut off valves. Insulate the pump house and exterior 

pumps and valves.

4.  Completely empty the tank.

Locate a GFCI (ground fault current interrupter) protected power source nearby. Typically a 2-4 outlet, 

15 amp, 110v, grounded, single phase service is sufficient. Refer to your electrical equipment specifica-

tions or consult a qualified electrician to determine power demands for your system.

Warnings

 To prevent electrical shock, disconnect all electrical devices before servicing the Skimmer.

Do not attempt to operate electrical devices with damaged cords or plugs.

Do not attempt to remove any electrical device from the Skimmer by pulling on its cord.

Jolie 

Products 

Inc

Summary of Contents for High Flow Skimmer HFS12500













Reviews: