manualshive.com logo in svg

Savaria V1504, Owner'S Manual, Page: 6 / 20

Share
Download
Savaria V1504 Owner'S Manual Download Page 6

6

V1504 Owner’s Manual

Part No. 000692, 30-m06-2017

2. GENERAL SPECIFICATIONS

V1504 Specifications

Load capacity

750 lb (340 kg)

Maximum travel

23 ft (7 m)

Travel speed

20 ft/min (0.1 m/s)

Levels serviced

2 (standard), 3, 4

Daily cycle

Normal: 30

Heavy: 75

Excessive: 100

Maximum starts in 1 hour on standard installation: 12

Cab sizes

36” x 48” (914 mm x 1219 mm)

36” x 54” (914 mm x 1371 mm)

36” x 60” (914 mm x 1524 mm)

Side guard panels

42-1/8” (1070 mm) high side guard panels on 
platform

Cab access

Enter/exit same side (platform Type 1L and 1R)

Front/rear access (platform Type 2)

90 degree access (platform Type 3 and 4)

Power supply

120 VAC, 20 A, 60 Hz, single phase

Motor/pump

24 VDC, 3 Hp (2.1 kW)

Gear type hydraulic pump

Control system

Electronic-free relay logic controller

Drive system

2:1 chain hydraulic drive system

Tower

Modular 8 ft (2.4 m) base guide rail assembly

Roller guide support

Pit depth requirement

3” (76.2 mm)

Finish

Beige electrostatic powder coat paint on all steel 
surfaces and vacuumed formed plastics

Summary of Contents for V1504





















Reviews:

No comments