background image

   

TC_car-BA-e-1712 

6  Battery replacement 

 

a) If the battery symbol ``+/-``appears on the display, batteries should be replaced. 
b)  The battery cover 3-4  has to be  removed from the instrument and the batteries 

have to be taken out. 

c) Batteries (4x1.5V AAA/UM-4) have to be installed, paying carefully attention to  
    polarity.  
d) If the instrument is not used for a longer period, batteries should be removed. 

7  Adjustment foils 

 
As accessory there is included a foil set of different adjustment  foils, which always 
cover the measurement range from 20 to 2000µm. It is also available as a spare part, 
article ATB-US07. 

8  Trouble shooting 

 
a)  The instrument should always be adjusted  on the  uncoated base material to be 
measured instead of the  base plate included in the delivery. Then the accuracy is 
more precise. 
b) Sensors will eventually wear off. Life of the sensor will depend on the number of 
measurements taken and how abrasive the coatings are. 

9  Restore Factory Settings 

 
a) It is recommended to restore factory settings in following cases: 

-  The instrument does not measure any more

 

-  Measurement accuracy is degraded caused by drastic environmental changes

 

b) How to restore: 
To restore factory settings includes both, “Fe” setting and “NFe” setting. Please note 
which symbol is shown on the display. 
You can restore only one of them or both respectively. Please follow the procedure 
below: 
- Press the Power key and do not release it until “CAL” appears on the display. OFF, 
UNIT, SC and the CAL will appear in sequence. CAL appears about 6 seconds from 
starting to press the Power key. 

F:H

 or 

nF:H 

will be displayed after releasing the Power key. 

Place the sensor (3-1) onto the corresponding base material steadily. 
Then press the Zero key which is followed by a “beep”. Lift the sensor for more than 
5cm. Then press the Zero key again and the gauge will return into measurement 
mode. Now factory setting is restored. 
 
Annotation:  
To have a look at the CE Declaration of Conformity, please click onto the following 
link: 

https://www.kern-sohn.com/shop/de/DOWNLOADS/

 

 

Summary of Contents for SAUTER TC car







Reviews: