SATO M10e Series Operator'S Manual Download Page 11

Page: 11 / 82

Section 1: Overview

SATO M10e

PN 9001101 Rev. A

Page 1-7

All specifications subject to change without notice.

ACCESSORIES AND OPTIONS

PCMCIA MEMORY

EXPANSION

One slot for PCMCIA Memory Card (up to 4 MB SRAM or 16 MB Flash

ROM). Can be used for graphic file storage, print buffer expansion, format

storage and downloaded fonts.

CALENDAR

An internal Date/Time clock that can be used to date/time stamp labels at

the time of printing.

LABEL CUTTER

An attachment allowing labels to be cut at specified intervals. Controlled

through programming.

COAX/TWINAX

INTERFACE

Coan/Twinax Plug-In Interface module. Coax interface emmulates an IBM

3287-2 printer with a stndard Type A BNC connector. Twinax interface

emulates IBM 5224, 5225, 5226 or 4214 printers with auto-terminate/cable

through capabilities.

PARALLEL INTERFACE

IEEE1284 Bi-Directional Plug-In Interface Module

SERIAL INTERFACE

High Speed RS232 Plug-In Interface Module

USB INTERFACE

Universal Serial Bus Plug-In Interface Module

ETHERNET INTERFACE

10/100 BaseT Plug-In Interface Module

Summary of Contents for M10e Series



















































































Search results

Summary of Contents for M10e Series

Reviews:

Related manuals for M10e Series

Brands by name

Popular brands

SATO M10e Series, Operator'S Manual

Search results

Summary of Contents for M10e Series

Reviews:

Related manuals for M10e Series

Brands by name

Popular brands