background image

A few seconds after System Power On, “satellite name” will appear
elevation angle set menu.

Elevation angles are set 
from 35 degree to 70 
degrees.  User’s can 
also choose elevation 
angle by location name.

Use up and down switch to choose your location and 
push set switch.  All settings are finished. Now push 
start switch and system will start searching satellite 
signals.

Elevation Angle  Setting 

Elevation Angle

/ Location name

Use up and down switch 

to set locations.

Example

(Australia)

 ↓ ↑

EL 70DEG

COOKTOWN

  ↓ ↑

EL 65DEG

TOWNSVIL

  ↓ ↑

EL 60DEG

BRISBANE

  ↓ ↑

EL 55DEG

DARWIN

  ↓ ↑

EL 50DEG

SYDNEY

  ↓ ↑

EL 45DEG

MELBOURN

  ↓ ↑

EL 40DEG

HOBART

  ↓ ↑

EL 35DEG

PERTH

Factory setting will be 50 degrees.  
After the first settings have been 
activated they will be automatically 
memorised.  There is no need to 
reset as long as you remain in the 
same location.

LCD window shows current status of auto searching system

H POL.
SELECTED 

18V from set top box (Vertical signal)

V POL.
SELECTED 

13V from set top box (Horizontal signal)

Only applicable for the above two cases (Linear signal)

CHECK.
STB CBL. 

Not connected with set top box- Check 
cable connected with STB-1

SIGNAL
DETECTED 

Satellite signal found

NIT
DETECTED 

Confirm the signal is right information from target 
satellite

SIGNAL
LOST. 

Cannot find satellite signals - check antenna 
direction

Antenna Type  
Input Frequency 
Output Frequency 
Antenna Gain
Antenna Size
Polarization 
Cross Polarization 
LNB Noise Figure
L/O Frequency
Output Impedance
Az Controll Range
EL Controll Range 
Power Supply
Operation Temperature
Storage Temperature
Humidity
Weight
Dimension

Parabolic 46 cm 
10.7-12.75 GHz 
950-2,050 Mhz 
33[dBi] / 35[dBi]
460mm / 600mm
Horizontal / Vertical  or  RHCP / LHCP
〈 -20dB min.
0.9dB max.

Suitable for most frequency ranges world wide

 

75[Ohm] 
360° ±10°
25∼80°  
AC100-240[V] / DC24[V]   
-30℃∼80℃  
-40℃∼85℃
95%@40degrees
7kg
460 x 460 x 410mm

DATA Update

Specification

future work

Data cable to PC for data update or download.

After antenna is locked in with 

satellite you may power off to

save unnecessary power usage.

Satellite name

Summary of Contents for PAPSA








Reviews: