Sapling SAI Series Installation Manual Download Page 8

Page: 8 / 54

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Wall Mount Installation - Round SlimLine Clock

Included in Package

Included in Wiring Kit (A-SLM-MK-S-1)

Included in Gang Box Kit (A-GB-MK-1)

Description

SAI round SlimLine
analog clock

Quantity

Picture

Mounting Piece

#6-19x7/16 screw

Strain Relief

#6-32x1 screw

#6-19x3/8 screw

(not used)

PLEASE NOTE:

A user will also have to provide a Phillips-head screwdriver, a small flat-blade screwdriver, a single gang box, any equipment needed to install

the gang box, and one AA battery. You may also need a 1/4 inch drill if you decide not to attach the clock directly to the gang box.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a
replacement kit.

Included in Wiring Kit (A-WK-MTG-1)

#8x1.5 Self-tapping screw

Wall anchor

Summary of Contents for SAI Series























































Search results

Summary of Contents for SAI Series

Reviews:

Related manuals for SAI Series

Brands by name

Popular brands

Sapling SAI Series, Installation Manual

Search results

Summary of Contents for SAI Series

Reviews:

Related manuals for SAI Series

Brands by name

Popular brands