background image

31

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

(+1) 215.322.6063 P.
(+1) 215.322.8498 F.
www.sapling-inc.com

Web Interface Programming

Synchronization

1.

 

Input Selection

  This drop-down list allows the user to select which input will control the master clock.  The choices are: 

• 

Real Time Clock

• 

58 Minute Sync_1

• 

National Time_Rauland 

• 

Wireless Repeater

• 

GPS

• 

58 Minute Sync_2

• 

Dukane Digital

• 

RS485

• 

NTP

• 

58 Minute Sync_3

• 

Rauland Digital

• 

59 Minute Sync

• 

58 Minute Sync_4

• 

Once a Day Pulse

If Once a Day Pulse is selected, then fields for hours, minutes and seconds will appear.  Enter the time (in 24 hour mode) that the clock is to 

go to when a once a day pulse is present.  It must be a minimum of a one second pulse.

2.

 

Backup Selection

  This drop-down list allows the user to select a backup input in case of the loss of the primary input.  In order to use 

the Backup Selection, the following protocols cannot be used as both a primary and secondary input:  59 minute sync, 58 minute 1-4 sync, 
National Time/Rauland, Dukane Digital, Rauland Digital and once a day Pulse.  An example of a configuration would be NTP being the 
primary input and 58 minute correction being a secondary input.   Setting the primary source to 59 minute sync and the secondary source to 
Dukane digital would be an incorrect configuration.

3.

 

Clock #1 Circuit

  This drop-down list allows the user to select the sync-wire output for the Clock #1 circuit.  The choices are:

• 

59 Minute Sync*

• 

58 Minute Sync_3*

• 

National Time_Rauland  2*

• 

58 Minute Sync_1*

• 

58 Minute Sync_4*

• 

Once a Day Pulse

• 

58 Minute Sync_2*

• 

National Time_Rauland_1*

• 

Rauland Digital

4.

 

Clock #2 Circuit

  This drop-down list allows the user to select the sync-wire output for the Clock #2 circuit.  See #3 above for the list of 

choices.

5.

 

Submit

  This button, when pressed, will save all of the information to the master clock.

6.

 

Cancel

  This button, when pressed, will clear out any changes made and will not save any data.

 

NOTE:  GPS is only valid if the option is purchased.

* See page 24 for protocol definitions

q

e

w

r

t

y

Summary of Contents for NTP 7000 Series








































Reviews: