background image

Security

Here users define the security type and level of the wireless network. Selecting 
different methods provides different levels of security.  Please note that using any 
encryption may cause a significant degradation of data throughput on the wireless 
link. There are five Encryption types supported: “None”, “WEP”, “WPA”, ”WPA2”, and 
“WPA-Mixed”. And 

TKIP/AES encryption security. 

Enabling any encryption can protect 

your data from eavesdroppers. If you do not need this feature, select “None” to skip 
the following setting.

Item

Description

WEP

WEP is the most general encryption scheme 
among wireless LAN security, configure the 
common encrypted key (WEP Key) for access 
point and wireless LAN handset. WEP key length 
are "64bit", "128bit", and "256bit" (This product 
corresponds up to 128bit), larger the value is, 
more the character can be set, and encryption 
strength will enhanced.

* If you configure the encryption key as "5 letters 
in half-width alphabets and numbers" or 
"Hexadecimal in 10 digits", please select "64-bit".
* If you configure the encryption key as "13 
letters in half-width alphabets and numbers" or 
"Hexadecimal in 26 digits", please select "128-
bit".

WPA / WPA2

WPA/WPA2 is wireless LAN security standard 
which is strengthen over WEP. On WPA-
PSK/WPA2-PSK, uses encrypted key called pre-
shared key, and set up common encryption key 
for access point and wireless LAN handset like 
WEP. There are "AES" and "TKIP" as encryption 
scheme. "TKIP" automatically updates the key at 
regular intervals, check and approve the 

Summary of Contents for BR261c





















































































Reviews: