– 5 –
5. Video Clip Recording and Playback
5-1. Recording
The signal from the camera block is input to IC101 (ASIC). The
data that is input to the ASIC is input to SDRAM, and converts
this data to encoded MPEG4 data, after which it is written in
sequence onto the SD card as streaming data. At this time,
the audio signals that are input to the built-in microphone are
converted into digital data by the audio CODEC IC of IC182,
and they are then input to ASIC. The audio data is then en-
coded (AAC), and then it is written in sequence onto the SD
card together as streaming data with the image signals de-
scribed above.
5-2. Playback
The data is read from the SD card, and the encoded data is
decoded into image data where it is displayed by the LCD or
on a TV monitor. At the same time, the audio data is also de-
coded, and is input to IC182 as digital data. D/A conversion is
carried out at IC182, and the sound is then output to the speaker
or to the LINE OUT terminal or the headphone.
6. Audio CODEC Circuit (IC182)
The audio signals from the microphone are converted into 16-
bit digital data. AD conversion is carried out at a maximum
sampling frequency of 48 kHz.
During audio playback, the 16-bit digital data is converted into
analog signals and these drive headphone through the speaker
or line out system and headphone amplifier. DA conversion is
carried out at a maximum sampling frequency of 48 kHz.
4. Lens drive block
4-1. Focus drive
The 16-bit serial data signals (LENS_SDI) and (LENS_SCLK
and LENS_EN) which are output from the ASIC (IC101) are
used to drive (FOCUS A +, FOCUS A -, FOCUS B + and FO-
CUS B -) by the motor driver IC (IC951), and are then used to
microstep-drive the stepping motor for focusing operation. De-
tection of the standard focusing positions is carried out by
means of the photointerruptor (F_SENSE) inside the lens block.
4-2. Zoom drive
The 16-bit serial data signals (LENS_SDI) and (LENS_SCLK
and LENS_EN) which are output from the ASIC (IC101) are
used to drive (ZOOM A +, ZOOM A -, ZOOM B + and ZOOM B
-) by the motor driver IC (IC951), and are then used to
microstep-drive the stepping motor for zooming operation. De-
tection of the standard zooming positions is carried out by
means of the photointerruptor (F_SENSE) inside the lens block.
4-3. ND filter
The 16-bit serial data signals (LENS_SDI) and (LENS_SCLK
and LENS_EN) which are output from the ASIC (IC101) are
used to drive (ND + and ND –) by the motor driver IC (IC951),
and then the ND filter is inserted into and removed from the
beam path.
4-3. Iris drive
The drive method is a galvanometer type without braking coil.
The output from the Hall sensor inside the lens is amplified by
the Hall amplifier circuit inside the IC951 lens drive IC, and the
difference between the current and target aperture determined
by the resulting output and the exposure amout (16 bit serial
signal (LENS_SDI) and (LENS_SCLK and LENS_EN)) output
from the ASIC (IC101) is input to the servo amplifier circuit
(IC951) to keep the aperture automatically controlled (DRIVE+
and DRIVE -) to the target aperture.
4-4. Shutter drive
Reverse voltage is applied to the above aperture drive coil to
operate the shutter. When the shutter operates, the SHUTTER
+ signal that is output from the ASIC (IC101) becomes high
(input to SHUTTER of IC951) and the shutter operates.
Summary of Contents for VPC-FH1BK - Xacti Camcorder - 1080p
Page 11: ... 11 MEMO ...
Page 27: ... 27 MEMO ...
Page 29: ...29 1 2 3 4 5 6 7 8 9 10 13 14 11 12 ...
Page 64: ......
