background image

 

Title 

Specifications of Lithium Ion battery (Prismatic Type) 

page 

13/13 

 

15. Warranty Period of Battery 

The warranty period of a cell is for one year after shipment. However, if a cell causes unusual 
operation within this period,

 

SANYO will replace by a new cell for free as long as it is clear 

that  the  cause  of  the  failure is  in  the  cell  manufacturing  process  and  the  cell  has  not  been 
used in the abnormal condition. 
 
 

16. Requirement for Safety Assurance 

For  the  sake  of  safety  assurance,  please  discuss  the  equipment  design,  its  system  and 
protection circuit of Lithium ion battery with SANYO in advance. 
And  also,  consult  SANYO  about  the  high  rate  current,  rapid  charge  and  special  application 
such as extreme condition and / or environment. 
 
 

17. Notice for Battery Swelling 

There is a possibility that swelling occur in usage of prismatic type cells. 
Regarding thickness of battery, the specified value described on the drawing is the 
thickness after 500cyc. under 4.3. 
(as specified in paragraph 4.3.) 
Therefore there is a possibility that battery thickness exceeds the specified value under the 
following conditions. 

The charging voltage is over 4.20V. 

・T

he ambient temperate of usage is not 25±2

℃.

 

The battery is used more than 500cycles. 

The battery is stored for a long time. 

 

File  No 

UF103450-849 

Energy Company, SANYO Electric Co., Ltd. 

Portable Rechargeable Battery Business Group 

Lithium-Ion  Battery  Business  Unit 

 

Summary of Contents for UF103450P-NETE-5
















Reviews: