background image

 

Title 

Specifications of Lithium Ion battery (Prismatic Type) 

page 

8/13 

11. Exemption from Warrantee 

  SANYO will not be responsible for trouble occurred by handling outside of the precautions 

in this specification. 

  SANYO  will  not  be  responsible  for  trouble  occurred  by  matching  electric  circuit,  battery 

pack, PDA and charger. 

  SANYO will be exempt from warrantee any defect cells during assembling after acceptance. 

 
12. Other Remarks 

  If  there  are  problems  in  this  specification,  SANYO  can  consider  to  change  specification 

after discussion. 

  About the things not covered by this specification, SANYO will have discussion. 

  Do not use this cell for other models or equipment. 

 

13. Standard Charging Method 

  If the cell voltage drops to 0V as a result of storage and the cell is charged at this 
condition, the FET on the protection circuit may generate heat.

 

The charger must have 

the pre-charge system. 

 

  Pre-charge  current  of  charger  should  be  approximately  0.18A.  When  the  battery 

voltage  becomes  3.0V/cell,  standard  charge  should  be  started.  When  the  battery 
voltage  is  less  than  3.0V/cell  even  after  the  set  period  of  timer,  charging  should  be 
stopped. 

 

  Standard charge is 1.88A/cell-4.20V/cell (Constant current-constant voltage). 

Charging should be suspended when the time, OCV or current is certain value. 

 

  The  cell  could  be  swelled  by  continuous  charging,  especially  under  the  high 

temperature atmosphere.   

         

 

Please consult SANYO regarding the detail for charging method. 

 

 

File  No 

UF103450-849 

Energy Company, SANYO Electric Co., Ltd. 

Portable Rechargeable Battery Business Group 

Lithium-Ion  Battery  Business  Unit 

Summary of Contents for UF103450P-NETE-5
















Reviews: