Sanyo TSL-4024P Instruction Manual Download

Page: 38 / 52

SETTING THE CASSETTE EJECT MODE

Cassette Eject Setup

When using two or more VCRs, the cassette tapes of all
the VCRs or some of the VCRs can be ejected at the
same time.

NOTE:

“TERMINAL SET” in the (OTHERS) menu should
always be set to “SET2”.

Press the STANDBY/ON button.

Press the MENU button to display the MAIN MENU.

Press the

(or

) button to select the “4.WARNING

OUT/CONTR. SET” line, then press the ENTER
button.

The (WARNING OUT/CONTROL SET) menu
appears.

<WARNING@OUT@SET>SET@UP

ALARM@@@@@@@@@@@@Y

NON@REC@@@@@@@@@@N

MECHA.PROBLEM@@@@Y

<CONTROL@SET>

EJECT@MODE@@@@@@@EJECT1

OPERATION@@@@@@@@SLAVE

Press the

(or

) button until the “EJECT MODE”

setting is highlighted, then press the ENTER button.

Press the

(or

) button to select the desired

cassette eject mode, then press the ENTER button.

EJECT1 . . . . The cassette is ejected only if the

VCR is not in recording or
recording pause mode.

EJECT2 . . . . The cassette is ejected only if the

VCR is in stop mode.

Press the

(or

) button until the “OPERATION”

setting is highlighted, then press the ENTER button.

Press the

(or

) button to select the desired

operation, then press the ENTER button.

SLAVE . . . . . The function is restricted to only

the VCR being operated.

MASTER . . . The function is applied to the VCR

being operated and all VCRs that
are connected after it.

Press the MENU EXIT button.

NOTE:

The EJECT button will not be operative during
recording mode.

Connection

Eject input (SERIES IN) terminal

Depending on the “EJECT MODE” setting in the
(WARNING OUT/CONTROL SET) menu (see
“Cassette Eject Setup”), the cassette loaded into the
VCR can be ejected when there is input to this
terminal.

Eject output (TIMER OUT) terminal

A signal is output from this terminal when the EJECT
button is pressed (if the VCR is set up as the
“MASTER” VCR; see step

under “Cassette Eject

Setup”) or when there is input (a trigger) at the
SERIES IN terminal, even if the security lock is set or
a cassette is not loaded.

NOTES:

The terminal names and signals are different from the
usual setting.

Names in brackets apply to terminals on the rear
panel.

VCR No. 1

VCR No. 2

To SERIES IN terminal

To COM terminal

SERIES IN

COM

TIMER OUT

SERIES IN

COM

TIMER OUT

NK4QG/EX (TLS-4024P GB) Tue. Sept., 10/2002

English

Summary of Contents for TSL-4024P





















































Search results

Summary of Contents for TSL-4024P

Reviews:

Related manuals for TSL-4024P

Brands by name

Popular brands

Sanyo TSL-4024P, Instruction Manual

Search results

Summary of Contents for TSL-4024P

Reviews:

Related manuals for TSL-4024P

Brands by name

Popular brands