Sanyo PLC-XE32, Service Manual

Page: 30 / 96

-30-
Electrical Adjustments
Group/
Item
Item Name Function Initial Range Note
150 PreCoast YCbCr 480i 7 0 - 63
151 PostCoast YCbCr 480i 13 0 - 63
15 PreCoast YCbCr 575i 7 0 - 63
153 PostCoast YCbCr 575i 13 0 - 63
154 PreCoast YCbCr 480p 7 0 - 63
155 PostCoast YCbCr 480p 13 0 - 63
156 PreCoast YCbCr 575p 7 0 - 63
157 PostCoast YCbCr 575p 13 0 - 63
158 PreCoast YCbCr 70p 60Hz 7 0 - 63
159 PostCoast YCbCr 70p 60Hz 13 0 - 63
160 PreCoast YCbCr 70p 50Hz 7 0 - 63
161 PostCoast YCbCr 70p 50Hz 13 0 - 63
16 PreCoast YCbCr 1080i 60Hz 7 0 - 63
163 PostCoast YCbCr 1080i 60Hz 13 0 - 63
164 PreCoast YCbCr 1080i 50Hz 7 0 - 63
165 PostCoast YCbCr 1080i 50Hz 13 0 - 63
166 PreCoast YCbCr 1035i 7 0 - 63
167 PostCoast YCbCr 1035i 13 0 - 63
180 PreCoast SCART 480i 7 0 - 63
181 PostCoast SCART 480i 13 0 - 63
18 PreCoast SCART 575i 7 0 - 63
183 PostCoast SCART 575i 13 0 - 63
Group 10 Sync Processor
0 SYNCAMPHLCKTOLOW
Minimum sync amplitude threshold for
HLCK 1 to 0 tansition
0x1000 0 - 9999
1 SYNCAMPHLCKTOHI
Minimum sync amplitude threshold for
HLCK 0 to 1 tansition
0x700 0 - 9999
Group 0 Video Decoder *R : Read Only Value
0 Y Level
Composite / S-Video - Y Level (ADC RGB
Gain)
10 / 10 0 - 55
1 C Level
Composite / S-Video - C Level (ADC
Saturation)
115 / 115 0 - 55 Composite / S-Video
3 XCXL Level
Cross-Chroma, Cross-Luma Level 3 0 - 5
4 CDNBANDWIDTH Comb D Narrow Bandwidth 3 / 3 0 - 3
5 CDWBANDWIDTH Comb D Wide Bandwidth 4 / 4 0 - 7 NTSC/PAL
6 CDCNMINLEAK
Comb D Chroma Narrow Band
Minimum Leakage
0 / 3 0 - 3
Left Values are adjustable if CXCL Level
= 5.
7 CDCNSLOPELEAK Comb D Narrow Band Slope Leakage 7 / 7 0 - 7
8 CDCWMINLEAK Comb D Wide Band Minimum Leakage 1 / 3 0 - 3
9 CDCWSLOPELEAK Comb D CW Slope Leakage 6 / 6 0 - 7
10 COMBLEAKBPGAIN Comb Leak To Ban Pass Gain 1 / 0 0 - 3
11 CDBDIAGONALGAIN Comb D Band Pass Diagonal Gain 1 / 3 0 - 3
1 CDNBCWBCLGAIN
Comb D Narrow Band Comb Wide
Band Comb
1 / 1 0 - 3
13 RLUMASETUP-Enable 7.5IRE Setup Enable 0 0 - 1 Effective only NTSC Signal
Group 40 General
0 IP Mode Sets for IP Off 1 0 - 1
0: IP Block not used
1: IP OFF used with IP Block
1 3: PullDown Mode 1 1 - 3
bit0 : Global Motion
bit1 : Video Motion
Detect Film Mode Enable 0 0 -
0 : :3pull down & :pull down
1 : :3pull down
: :pull down
3 Force IP Mode 0 -
0 : IP Process Disable
1 : Force Normal IP Mode
: Force Film Mode
Effective only for PSF Signal.
Group 41 Deinterlacer setting Effective only for Progressive ON-L1 mode.
0 Motion Adaptive Weight Value <KDEINT> 30 0 - 55
1 Angle Interpolation Level 0 : Conservative <====> 4 : Aggressive 4 0 - 4
CUE Low Pass Filter Enable <CUELPFEN> 0 0 - 1
Group 4 Deinterlacer setting Effective only for Progressive ON-L mode.
0 Motion Adaptive Weight Value <KDEINT> 0 0 - 55
1 Angle Interpolation Level 0 : Conservative <====> 4 : Aggressive 0 - 4
CUE Low Pass Filter Enable <CUELPFEN> 0 0 - 1
Group 43 Deinterlacer setting Effective only for Progressive ON/Film mode.
0 Motion Adaptive Weight Value <KDEINT> 30 0 - 55
1 Angle Interpolation Level 0 : Conservative <====> 4 : Aggressive 4 0 - 4
CUE Low Pass Filter Enable <CUELPFEN> 0 0 - 1
Group 45 Noise Reduction (Time) Effective only for N.R - Off