Sanwa MT-R RX-493i, User Manual

Page: 6 / 31

10 9
Connections and Installation of Receiver
Connection
&
Installation of Receiver
Connection
&
Installation of Receiver
10 9
接続について
*Indicate receiver working condition by LED light.
Indication of Receiver Working Condition by LED light
Connected
Blue light On
*When binding with 2 transmitter,
blue light flush at 2 sec intervals.
In BIND Setting
Blue light flushing
Blue light blinking
Blue and red light on
NOT Connected
Battery Fail Safe Working
Red light on
Receiver is not connected
in Battery Fail Safe working
CH4: 4ch
SSL/BAT: BIND/SSL Port
* Please do not connect devices except SANWA SSL
Compatible devices.
CH3: 3ch
CH2: Throttle (ESC / FET Speed Controller)
CH1
:
Steering
BIND Plug
LED
Antenna
Antenna pipe amount
Please use SANWA antenna pipe.
Antenna Pipe
Antenna
■Case of connecting PGS servo to 2 SSL ports
■Case of connecting PGS servo and SUPER VORTEX Gen2/PRO/SUPER VORTEX Stock to SSL port
●
Connection example in case of using in EP car
Please refer the below picture for receiver and servo connection
Switch harness
Connect the receiver battery
Connection with BATT
Connection with
CH2
Connection with CH1
Power battery
Motor
ESC / FET speed controller
Steering servo
Throttle servo
Connection with CH1
Connection with CH2
Steering servo
CH2
BATT
CH1
CH2
BATT
CH1
SUPER VORTEX Gen2/PRO
/SUPER VORTEX Stock
●Set AUX TYPE of the transmitter for both AUX1, AUX2 to CODE 10.
AUX1 CODE10: Setting of SUPER VORTEX Gen2 / PRO /SUPER VORTEX Stock can be from the transmitter.
AUX2 CODE10: Setting of each of the parameters of PGS
Ⅱ
servo can be from transmitter.
Note) In SUPER VORTEX Gen2 / PRO, do not assign function to CODE 10 of AUX2 by code
assign of PROGRAM BOX Gen2. It interferes with CODE 10 of AUX2 of PGS servo and suitable
setting cannot be done.
Note) Set SSL
－
CH of PGS servo to [1].
(Factory setting of PGS servo is [1].)
Note) CODE of AUX2 is used for SUPER VORTEX ZERO / SUPER VORTEX TYPE-D /
SUPER VORTEX SPORT. It interferes with CODE 10 of AUX2 of PGS servo and
suitable setting cannot be done. Therefore, it cannot be used along with SSL of PGS servo.
Note)When Connecting PGS servo with SGS-02 cannot change setting at the same time.
When using SGS-02, Gain connector connect to SSL port.
*Please DO NOT connect another devices except SANWA SSL compatible products.
About setting and connection, please refer manuals of SSL compatible product.
Short Y harness
Steering servo
PGS servo
：
SSL - CH1 setting
SSL Port
Connect the receiver battery
●Set AUX TYPE of AUX2 of the transmitter to CODE 10.
AUX2 CODE10: Setting of each of the parameters of PGS servo can be done from the transmitter.
Note) Set SSL
－
CH of PGS servo used in steering servo to [1].
Set SSL
－
CH of PGS servo used in throttle servo to [2].
(Factory setting of PGS servo is [1].)
Note) In case of setting each parameter by the function of CODE10 of AUX2, setting of PGS
servo of SSL
－
port set by CODE1 of AUX2 can be directly changed from the transmitter.
PGS servo not specified by CODE1 of AUX2 works on the parameters saved inside.
PGS servo: SSL - CH1 setting
Steering servo
Throttle servo
Switch harness
Short Y harness
PGS servo: SSL 2 CH2 setting
SSL Port
Other Empty Port
*Please, refer on our Website about any other examples. http://www.sanwa-denshi.co.jp
*When using PGS Servo with SGS-02,
PGS servo cannot set by CODE10 at the same time.
Only SGS-02 can be set when connect with PGS servo.
ABOUT THE RECEIVER
ABOUT HANDLING THE ANTENNA
ABOUT CONNECTION SETUP
● RX-493i
RX-493i can evaluate received signal strength and packet delivery ratio from transmitter.
*MT-R cannot check received signal strength and packet delivery ratio.
RX-493i can store 2 transmitter ID Number. It is able to combine using individual transmitter which is
different setting in endurance race .
If you bind with 2 different transmitter, the receiver store the different transmitter and can operate by
transmitters without re-bind.
*CANNOT operate by the 2 different transmitter at the same time. 2 ID store system is only compatible
with M17, MT-5, or MT-R.
Throttle neutral position or operation quantities might be different each transmitter. Please adjust each
transmitter setting to fit chassis linkage.
When setting SSL compatible devices by MT-R CODE AUX function, please connect SSL compatible
device to SSL port.
MUST set fail-safe setting on each transmitter.
Please set same RF mode and response mode as 1st transmitter when you bind 2nd transmitter. If it was
different mode, cannot bind with 2 transmitters.
*If 2nd transmitter was different RF node and response mode from 1st transmitter, 1st transmitter ID No. is
deleted and only write 2nd transmitter.
*If you bound 3rd transmitter, 1st transmitter ID No. will be deleted.
*When using first time, please bind with receiver. (p.43)
● Reception distance may vary depending on the location
where the receiver and the antenna are installed.
● To protect the reception part (3 cm from the top) of the
antenna, make sure to place the antenna in the antenna
pipe as shown in the right illustration so that the top of the
antenna is not exposed outside of the antenna pipe.
● Don’t bend the antenna reception part or the antenna
coaxial cable because breaking can occur inside.
● Don’t pull the coaxial cable forcefully. It may damage the
receiver interior.
● Install the antenna on an RC car so that the antenna
reception part is in as high place as possible.
● Don’t cut or bind the antenna reception part or the antenna
coaxial cable since the receiver sensitivity might decrease.
● Keep the receiver antenna away from the motor and the
ESC / FET Speed Controller (including cables) and raise it
straight.
Note
• If the connector is disconnected due to a vibration during operation, it can cause runaway. Connect the connector
of the receiver, servos and switches securely.
• Because the receiver is susceptible to vibration, impact and water, make sure to take measures for vibration-proof
and waterproof. Negligence of taking these measures can cause runaway.
• When installing the receiver, keep the receiver away from a carbon chassis and metallic chassis.
• If metal parts installed on an RC car touch each other, it can cause noise that affects reception performance and it
can cause runaway.
• Make sure to install a noise killer condenser on the brush motor for electric RC cars. Without a noise killer
condenser, it can cause noise and runaway.
• For R/C System parts such as the transmitter, receiver, servos, ESC (FET Speed Controller) and transmitter
battery, use genuine SANWA products.
*When combining products other than genuine SANWA products, modifying, adjusting or exchanging parts is
done at a place other than SANWA, we do not take any responsibility.