Sanwa MT-R RX-493i, User Manual

Page: 24 / 31

46 45
How to Use Each Feature
How to Use Each Feature
How to Use Each Feature
Features assigned to the Switch and Trim
at the factory
TR1: Steering Trim(TRM-ST)
TR2: Throttle Trim(TRM-TH)
TR3: Dual Rate ST(D/R-ST)
SW1: TIMER
SW2: AUX1
SW3: AUX2 Sw1
Sw3
Sw2
Trm2
Trm1
Trm3
TRIM 3
(TRM 3)
TRIM 1
(TRM 1)
SWITCH 2
(SW 2)
SWITCH 1
(SW 1)
SWITCH 3
(SW 3)
TRIM 2
(TRM 2)
ENTER BACK
ENTER BACK
About MODE Setting for SW3
P1/P2 can be changed freely.
TWEAK1
Neutral
P1 P2
① ② ③
OFF, ASIST-ST, D/R-ST, D/R-TH, D/R-BR, CUR-ST, CUR-TH, SPD-ST, SPD-TH,
ALB, OFFSET, AUX1, AUX2, TIMER, TE-CLR, LOGGER
SW1
Assignable Futures
OFF, ASIST-ST, D/R-ST, D/R-TH, D/R-BR, CUR-ST, CUR-TH, SPD-ST, SPD-TH,
ALB, OFFSET, AUX1, AUX2
SW2
OFF, D/R-ST, D/R-TH, D/R-BR, CU-R-ST, CU-R-TH, CU-R-BR, SP-ST-F, SP-ST-R,
SP-TH-F, SP-TH-R, ALB-ST, ALB-LG, ALB-CY, OFFSET,
AUX1(CD1
～
10), AUX2(CD1
～
10)
SW3
TWEAK2 P1 Neutral P2
Switch
Assignable Futures Switch
Assignable Futures Switch
OFF
、
TRIM-ST, TRM-TH, TRIM-A1, TRIM-A2, D/R-ST, D/R-TH, D/R-BR, CU-R-ST, CU-R-TH, CU-R-BR,
SP-ST-F, SP-ST-R, SP-TH-F, SP-TH-R, ALB-PO, ALB-ST, ALB-LG, ALB-CY, OFFSET,
AUX1(CD1
～
10), AUX2(CD1
～
10)
TRIM1
TRIM2
TRIM3
Assignable Futures Switch
SYSTEM MENU
SYSTEM
KEY ASSIGN SWITCH
KEY ASSIGN TRIM
● A feature for setting system of the transmitter, such as Bind, Key Assignments (KEY ASSIGN),Buzzer,
Battery, LCD and CALIBRATION.
Switch and Trim position
● You can assign features to the switches (SW1, SW2, SW3) of the transmitter and toggle ON/OFF of the
features during operation.
1) Select [SYSTEM] with up and down key.
Determine with the Enter operation.
2) Select [KEY ASSIGN] with up and down key.
Determine with the Enter operation.
3) Setting the Switch (SW1/SW2/SW3)
Operate the Enter with [SW] and set the feature
to assign to the switch with up and down key.
○ Setting Range:
○ Default : SW1: TIMER SW2: OFF SW3: OFF
*BY Setting [ASSIST-ST] onto SW1 and SW2,
you can turn ON/OFF the feature of D/R, SPEED and CURVE
that can be set onto the steering.
4) Setting Mode
It sets the switch performance but there are casesthat
you cannot set depending on the feature to assign.
○ Setting Range
TOGGLE (Switching between ON/OFF when pressed every time)
PUSH (ON is worked when switch is only pressed)
● You can change the setting value of each feature with Trim1 - Trim3.
● You can also change the setting of the variation change in one time of Trim operation with the STEP
setting and the direction of the action with the REV setting.
1) Select [SYSTEM] with up and down key.
Determine with the Enter operation.
2) Select [KEY ASSIGN] with up and down key.
Determine with the Enter operation.
3) Setting Trim (TRM1/TRM2/TRM3)
Select [TRIM] with enter. Change the setting
and set a feature to assign with up and down key.
○
Setting Range:
○ Default: TR1:TRM-ST
TR2:TRM-TH
TR3:D/R-ST
4) Setting Step
Set the variation of the movement by one-time Trim operation.
Select [STEP] with up and down key. Determine with the Enter operation and set the variation.
○ Setting Range: 1 ～ 100
○ Default: 5
5) Setting the Direction of Action
Set the direction of action when operating Trim. Select [REV] with up and down key.
Determine with the Enter operation and set the direction of action.
○ Setting Range: NOR/REV
○
Default: NOR