(6901-002111 <02>)
15
6 Einstellungen
Siehe Seite 11
1.
Stellen Sie die Spannung für die Drehung nach rechts/links ein.
ACHTUNG:
Entfernen Sie die Spannmuttern
(A)
nie vollständig. Vergewissern Sie sich, dass die Gewinde über die Muttern herausstehen.
2.
Stellen Sie die Spannung zum Ausziehen/Einfahren des Arms ein.
3.
Stellen Sie die Spannung für die Neigung nach oben/unten ein.
2 Wandmontage Montage an Holzbalken
Siehe Seite 7
2-1 Suchen Sie die Balken
Hilfe zum Bestimmen der geeigneten Wandplattenposition finden Sie unter Height Finder auf sanus.com.
Suchen Sie die Balken. Stechen Sie mit einer Ahle oder einem dünnen Nagel die Mitte des Balkens bzw. der Balken an, oder verwenden Sie einen Kante-zu-
Kante-Balkensucher.
VORSICHT:
Vermeiden Sie Verletzungen und Sachschäden!
Ù
Jegliches Material, das die Wand bedeckt, darf 16 mm (5/8 Zoll) nicht überschreiten.
Ù
Mindestmaße der Holzbalken: üblich 51 x 102 mm (2 x 4 Zoll) (nominell 38 x 89 mm /1,5 x 3,5 Zoll).
2-2 Markieren Sie Bohrstellen an der Wand
Siehe Seite 7
Richten Sie die Wandplatte
[02]
aus und markieren Sie die Stellen für die Bohrlöcher.
HINWEIS:
Der Fernseher lässt sich in der Ausgangsstellung 9 cm (6 Zoll)
nach rechts oder links verschieben. Berücksichtigen Sie dies bei der Auswahl der Montagestelle für die Wandhalterung.
2-3 Bohren Sie Vorbohrungen
Siehe Seite 7
Bohren Sie Vorbohrungen wie in der Abbildung dargestellt.
Vorbohrungen
MÜSSEN
mit einem 5,5 mm-Bohrer (7/32 Zoll) bis zu 89 mm (3,5 Zoll) tief gebohrt werden.
2-4 Anziehen der Ankerschrauben
Siehe Seite 7
Ziehen Sie die Ankerschrauben an.
VORSICHT:
Vermeiden Sie Verletzungen und Sachschäden! Eine
unsachgemäße
Verwendung
kann
die
Haltekraft
der
Ankerschraube
verringern.
Vermeiden
Sie
Verletzungen
und
Sachschäden:
Ù
Ziehen Sie die Ankerschrauben
[17] NICHT
zu fest an.
Ù
Ziehen Sie die Ankerschrauben nur so weit an, bis die Unterlegscheiben
[16]
fest an der Wandplatte
[02]
anliegen.
2 Wandmontage
Massivbeton oder Betonblöcke
Siehe Seite 8
2-1 Markieren Sie Bohrstellen an der Wand
Siehe Seite 8
Hilfe zum Bestimmen der geeigneten Wandplattenposition finden Sie unter Height Finder auf sanus.com.
Richten Sie die Wandplatte
[02]
aus und markieren Sie die Stellen für die Bohrlöcher.
VORSICHT:
Vermeiden Sie Verletzungen und Sachschäden!
Ù
Montieren Sie die Wandplatte
[02]
direkt an der Betonfläche.
Ù
Mindestdicke der Massivbetonwand: 203 mm (8 Zoll)
Ù
Mindestmaße der Betonblöcke: 203 x 203 x 406 mm (8 x 8 x 16 Zoll)
2-3 Einsetzen der Dübel und Ankerschrauben
Siehe Seite 8
Setzen Sie die Ankerschraubendübel
[18]
ein. Führen Sie dann die Ankerschrauben
[17]
durch die Wandplatte
[02]
in die Dübel ein.
VORSICHT:
Vermeiden Sie Verletzungen und Sachschäden! Eine
unsachgemäße
Verwendung
kann
die
Haltekraft
der
Ankerschraube
verringern.
Vermeiden
Sie
Verletzungen
und
Sachschäden:
Ù
Stellen
Sie
sicher,
dass die Dübel
[18]
bündig
mit
der
Betonfläche
abschließen.
Ù
Ziehen
Sie
die
Ankerschrauben
[17]
nur
so weit an,
bis die Unterlegscheiben
[16]
fest
an
der
Wandplatte
[02]
anliegen.
Ù
Ziehen Sie die Ankerschrauben
[17]
NICHT
zu
the
fes
an.
2-2 Bohren Sie Vorbohrungen
Siehe Seite 8
Bohren Sie Vorbohrungen wie in der Abbildung dargestellt.
VORSICHT:
Vermeiden Sie Verletzungen und Sachschäden!
Ù
Vorbohrungen
MÜSSEN
mit
einem
10-mm-Bohrer
(3/8
Zoll)
bis
zu
89
mm
(3,5
Zoll)
tief
gebohrt
werden.
Ù
Bohren
Sie
niemals
in den
Mörtel
zwischen
den Blöcken.
3 Befestigen des Arms an der Wandplatte
Siehe Seite 9
4 Befestigen des Fernsehers am Arm
Siehe Seite 9
Positionieren Sie den Arm
[03]
so, dass ein Winkelstück an der Wand lehnt. Ziehen Sie Einstellschraube
(T)
an, um zu verhindern, dass sich der Arm während
der Montage der Anschlussplatte des Fernsehers bewegen.
Befestigen Sie die Anschlussplate
[01]
des Fernsehers an der Armvorrichtung
[03]
. Wenn die Teile richtig zusammengebaut wurden, rasten sie mit einem
klickenden Geräusch ein.
NEIGEN SIE DEN FERNSEHER NACH OBEN.
Setzen Sie die Feststellschraube
[13]
ein und ziehen Sie sie fest.
Richten
Sie
die
Löcher
oben
und
unten
am
Arm
[03]
mit
den
Schlitzen
in
der
Wandplatte
[02]
aus.
Befestigen Sie die Platten
[21]
und
den
Arm
[03]
mithilfe
der
Schrauben
[20]
und
Unterlegscheiben
[19]
an der
Wandplatte
[02]
. Ziehen Sie die Schrauben
mit dem Inbusschlüssel
[23]
fest.
5 Kabelführung
Siehe Seite 10
Entfernen Sie die Armabdeckungen.
Ziehen Sie die Arme vollständig aus und verlegen Sie die Kabel durch die Arme. Lassen Sie genug Spiel, um ein Überdehnen der Kabel beim Bewegen des
Arms zu verhindern.
Bringen Sie die Armabdeckungen wieder an. Bringen Sie die obere und untere Abdeckung
[22]
an.
6-1
Siehe Seite 11
Einstellen
der Höhe.
A.
Lösen Sie
die Schrauben
B.
Stellen Sie
die Höhe ein
C.
Ziehen Sie die Schrauben
wieder an