Sanitron S17A Owner'S Manual Download Page 5

5

INSTALLATION

L

OCATION

1.  The water purifi er is intended for indoor use only. The water purifi er is designed to mount horizontally. The water purifi er 

should be protected from the elements and from temperatures below freezing. The ambient temperature, in the area 
surrounding the water purifi er, should be between 35

o

 F and 100

o

 F.

2.  Electrical power supplied to the water purifi er 

MUST

 match power requirements listed on the water purifi er. Use of a voltage 

surge protector is recommended.

3.         Plug water purifi er only into an approved ground fault circuit interrupt (GFCI) receptacle.

4.  The water purifi er should be located in a dry, well-lit area, which provides enough room to perform routine maintenance. This 

includes a minimum distance of one chamber length from the wiper end, to allow for cleaning and/or the changing of the 
lamp and quartz sleeve as well as a minimum of 6” on the opposite end of the water purifi er. Minimum clearance to fl oor 18’’.

5.  The water purifi er should always be located closest to the point of use. This reduces the chance of the purifi ed water being 

re-contaminated by bacteria in the water distribution system after the water purifi er.

6. 

CAUTION:

 As with any water handling device, the water purifi er should be located in an area where any possible 

condensation or leakage from the water purifi er, any purifi er accessory and/or plumbing will not result in damage  to the 
area surrounding the water purifi er. For added protection, it is recommended that a suitable drain pan be installed under the 
purifi er. The drain pan must be plumbed to an adequate, free fl owing drain to prevent water damage in event of a leak. There 
are numerous leak detection/fl ood stop devices, available on the market today, designed to stop fl ow of water, reducing the 
chance of water damage due to leakage. For more details regarding leak prevention and/or limiting damages due to leaks 
please contact factory.

7.  The water purifi er should be located after all other water devices, such as De-ionizers, Water Softeners, Carbon Filters, Pre-

Filters, Reverse Osmosis, Pressure Tanks, and Pumps. This reduces the chance of the purifi ed water being re-contaminated by 
bacteria in any of these units.

D

IMENSIONAL

 D

ATA

Figure 1 - SANITRON

®

 Dimensional Drawing

Table 2 - SANITRON

®

 Dimensional Data

Model

A

B

C

D

E

F

G

H

J

Inlet/Outlet

S17A

8-3/4”

17”

8-3/4”

10”

17-3/8”

3-5/8”

4-5/16”

8-3/16”

7-3/16”

3/4”m NPT

S23A

14-3/4”

23”

13-1/4”

14-1/2”

23-3/8”

3-5/8”

4-5/16”

8-3/16”

10-3/16”

3/4”m NPT

S37C

28-1/2”

37”

16”

18”

37-3/8”

4-15/16”

5-11/16”

9-1/2”

11-1/8”

1”m NPT

S50C

40-7/8”

50”

26”

30”

50-3/8”

4-15/16”

5-11/16”

9-1/2”

13-13/16”

1- 1/2”m  NPT

All specifi cations, dimensional data, etc are approximate and subject to change without notice.

Summary of Contents for S17A





















Reviews: