Sanitron S17A Owner'S Manual Download Page 3

3

SAFETY WARNINGS

SAFETY INSTRUCTIONS

• 

All personnel should be alerted to the potential hazards indicated by the product safety labeling on this unit.

• 

The following conventions are used to indicate and classify precautions in this manual and on product safety labeling. Failure to 
observe precautions could result in injury to people or damage to property.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. 
Obey all safety messages that follow this symbol to avoid possible injury or death. 

WARNING: To guard against injury, basic safety precautions should be observed, including the following

:

1.  Read and follow 

ALL

 safety instructions.

2.  Do not use this water purifi er for other than its intended purpose as described in this manual.

3.  Do not alter design or construction.

4.  Do not remove any labels or devices.

5. 

DANGER: To prevent the risk of severe or fatal electrical shock, special precautions must be taken since water 

is present near electrical equipment. Always disconnect power before performing any service or maintenance.

6. 

WARNING: Avoid exposure to direct or refl ected germicidal ultraviolet rays. Germicidal ultraviolet rays are 

harmful to the eyes and skin.

7.  Intended for indoor use only. The water purifi er should be protected from the elements and from temperatures below freezing.

8.  Do not operate water purifi er if lamp cable, lamp connection, power cord and/or plug are damaged, or if any other damage to 

the water purifi er is visible or suspected

9.  Electrical power supplied, to the water purifi er, 

MUST

 match power requirements listed on the water purifi er.

10.   

Plug the water purifi er only into an approved ground fault circuit interrupt (GFCI) receptacle.

11. 

WARNING: Do not operate without proper electrical ground.

12.  Do not exceed water purifi er’s maximum rated fl ow capacity.

13.  Do not exceed maximum operating pressure of 100 PSI.

14.  Read and follow all notices and warnings on the water purifi er.

15. 

SAVE THESE INSTRUCTIONS.

This symbol/pictorial is used to identify the need to 
wear protective gloves.

!

Caution indicates a 

POTENTIALLY

 

hazardous situation, which, if not avoided, 

MAY

 result in minor or moderate injury.

Caution used without the safety alert symbol in-
dicates a potentially hazardous situation, which, 
if not avoided, may result in property damage.

This symbol/pictorial is used to identify an 

ULTRAVIOLET LIGHT

 hazard.

This symbol/pictorial is used to identify an 

ELECTRI-

CAL SHOCK

 or 

ELECTROCUTION

 hazard.

Warning indicates a 

POTENTIALLY

 

hazardous situation, which, if not avoided, 

COULD

 result in death or serious injury.

This symbol/pictorial is used to identify the need to 
wear approved ultraviolet blocking eyewear.

This symbol/pictorial is used to identify the need to 
wear approved ultraviolet blocking face shield.

This symbol/pictorial is used to identify components 
which must not be disposed of in trash

SAFETY LABELS

CAUTION

Danger Label: Hazardous Voltage 
and Ultraviolet Radiation (00-0196A1)

It is the user’s responsibility to determine and validate the 
suitability of this equipment for use in the user’s system or 
process.

No warranty or representation is made by the manufacturer 
with respect to suitability or performance of this equipment 
or to the results that may be expected from its use.

The user should periodically inspect, clean as necessary 
and confi rm the presence and good legibility of the product 
safety labels. Contact the factory for replacement labels in 
the event that any of the labels are missing or illegible.

Danger indicates an

 IMMINENTLY 

hazardous situation, which, if not avoided, 

WILL

 result in death or serious injury.

Location of Danger Label
(00-0196A1)

Summary of Contents for S17A





















Reviews: