background image

Installation & Operation Manual                                                                                               Merlin GDP4 

 

 

Rev: 11   03-21

 

6  

   

Wiring your Detector 

 

 

Power is supplied to a detector via the GDP terminal [+ / -] and using the panel [GAS DETECTION ZONE] terminal.  
If you are using a GDP panel you will need to use the detector [C/L] terminal as an alarm relay. 

 

   BMS Switch

 

 

The GDP4 can be integrated with a BMS to make or break a circuit on gas on/gas off, (valve open or valve closed). 

This will tell the BMS whether or not electrical power is being sent to the solenoid. There is a dip-switch located on 
the GDP4 circuit board labelled [BMS]. This is factory set to ‘OFF’ position which signals the BMS on gas on/gas off.  
When switched to ‘ON’, the GDP4 will only signal the BMS on a fault, i.e. gas detected, EM Stop pressed, etc.  
 

BMS SWITCH 

BMS SIGNAL 

OFF 

Gas on or off only. 

ON 

Error condition i.e. gas detected, emergency stop pressed. 

 

   Auto Reset Switch

 

 
The panel has a built-in auto reset feature. There is a dipswitch located on the circuit board labelled [AUTO RESET].  
This is factory set in the ‘Off’ position i.e. when power is restored after a power cut or loss, the panel has to be 
restarted manually. When enabled, the system will restart automatically when power is restored and can be reset 
following a fire alarm and when the alarm is cleared. 
 

AUTO SWITCH 

CONDITION 

OFF 

Panel has to be restarted manually following a power cut/loss and/or alarm. 

ON 

Panel will automatically restart when power is restored and can be reset remotely via a fire panel. 

 

   Zone 1 - 4 Set-Up Switches

 

 
There are dip-switches located on the GDP4 circuit board labelled [ZONE 1] to [ZONE 4]. 
This is factory set in the ‘Off’ position. For each of the gas detector zones you are using please ensure that the 
relevant zone has being enabled. The zones you are not using should be left disabled.  

 

ZONE 1/2/3/4 SWITCH 

CONDITION 

OFF 

Gas detection zone disabled. 

ON 

Gas detection zone enabled. 

 

Summary of Contents for Merlin GDP4













Reviews: