SandenVendo HFDM00002 Operation Manual Download

Page: 11 / 12

SANDENVENDO AMERICA INC

1188858N ECN 56775

Bag & Tong Holders

Top Mount Shelf

Sign Holder

Setup Instruction (Optional) HFDH & HFDHC Accessories

VDPCAA004: Right Side
VDPCAA005: Left Side

1246267

1246232

Step 3: Reinstall
bolt into top front
side glass.
Once front bolt is
installed, repeat for
the top back bolt.

Step 4: Repeat
steps 1-3 for the
left side bag &
tong holder if
applicable.

Step 1: Remove
the two magnetic
strips from inside
and protective
coating from
stainless.

Step 2: Remove
backing from
magnetic strips
and apply the
adhesive side to
the underside of
the tray.

Step 3: Place sign
holder on the top
center of the
Display.

Step 1: Remove
the two magnetic
strips from the
back side and
protective coating
from stainless.

Counter: VDPHDC001

Step 2: Remove
backing from
magnetic strips
and apply the
adhesive side to
the underside of
the sign holder.

Step 2: Remove
Rubber seal, place
bolt and washer
through bag &
tong holder
mounting hole.
Place rubber seal
over bolt on the
inside.

Step 1: Remove
top front plastic
side glass bolt.

Step 3: Place tray
on the top front of
the display and
align with the front
edge.

Summary of Contents for HFDM00002












