manualshive.com logo in svg

Sandel SN3308, Installation Manual

Share
Download
Sandel SN3308 Installation Manual Download Page 36

 Sandel 

Avionics

 

SN3308 Navigation Display 

Installation Manual 

90106-IM-G(4) Installation Manual W SIG.doc 

Page 36

P2-30:  GPS SELECTED Input

This input is used when the SN3308 is set up for slave mode so an 

external

GPS switch can be used to switch to an external GPS receiver.  Causes 
proper mode switching and annunciation on the SN3308 display.  This input is 
active only when enabled in the System maintenance page. 

P2-13: Reserved for Future Use
P2-32: OBS-/LEG, HLD-/AUTO or PAR TRK- Annunciator Input

For selected GPS-1 receiver with OBS/LEG mode (or HOLD/AUTO), this input 
when low senses and annunciates OBS or HOLD on the SN3308 display and 
changes the mode of the course pointer from auto-slew to manual control.  
Otherwise, this is used as a PAR TRK input for other types of receivers, based 
on the selection in the LNAV maintenance page. 

P2-14: External Switch 2 In.

See P2-22. 

P2-33: Spare Input 1

Reserved for future use.

P2-15: Inner Marker Beacon Input 
P2-16: Outer Marker Beacon Input 
P2-34: Middle Marker Beacon Input 

Marker beacon receiver inputs.  Normally connected to the external lamp 
drivers on the marker beacon receiver, see the installation drawings.   Most 
marker beacon receivers use “DC” ground referenced outputs driven by 
transistor drivers. All such receivers are compatible as shown on the 
installation drawings.  Some very old designs may use transformer outputs 
which are AC coupled.  In such an instance call Sandel for installation 
guidance.

P2-17: ADF-1 AC-X or DC-SIN Input  
P2-35: ADF-1 AC-Y or DC-COS Input  

Inputs from ADF-1 Receiver. Selection of AC/DC operation is on the ADF 
maintenance page.  For DC use P2-18 as the DC reference input.  For AC 
inputs Z is grounded.  24 AWG twisted shielded pair wire is recommended for 
these functions. 

P2-18: ADF-2 AC-X or ADF-1 DC Ref  
P2-36: ADF-2 AC-Y or ADF-2 DC Ref  

Used as DC REF inputs when DC Sin/Cos ADF is used as ADF-1 or ADF-2.  
Used as AC X/Y if ADF-2 is AC.  The DC function is activated when ADF-1 is 
selected as a DC receiver in the ADF-1 maintenance page. For AC inputs Z is 
grounded.

P2-19: ADF-2 DC-SIN or 400Hz Diff. Resolver SIN 
P2-37: ADF-2 DC-COS or 400Hz Diff. Resolver COS 

Summary of Contents for SN3308

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands