background image

S&C ELECTRIC COMPANY

716-600 

INSTRUCTION SHEET

Page 22 of 24
February 11, 2002

S&C Series 2000 Circuit-Switchers

Interrupter Replacement

Outdoor Transmission (69 kV through 230 kV)

Programming the Receiver

After replacing an interrupter and transmitter, the remote
gas-density monitoring system must be reprogrammed.
Programming “teaches” the receiver which transmitter
radio signal corresponds to which interrupter. 

A series of prompts on the LCD will guide you through

the programming process.

Step 45

Attach the magnet tool to a hotstick long enough to reach
the transmitter. The magnet tool, furnished with the origi-
nal switch, is located on the inside of the switch operator
door.

Step 46

Press—and hold for 10 seconds—the system set-up
button located on the right side of the receiver. See
Figure 20. The receiver unit will start to count down. See
Figure 21. Release the set-up button when prompted. See
Figure 22. This will put the receiver in setup mode.

NOTICE

 

All phases must be reprogrammed when an interrupter
is replaced.

NOTICE

 

Inadvertently releasing the set-up button during
countdown will stop set-up and reset the receiver in
regular monitoring mode.

INTERRUPTERS WITH THE REMOTE GAS-DENSITY MONITOR OPTION — Continued

Figure 20. Location of set-up button on receiver.

Figure 21. Receiver LCD while pressing and holding set-up
button.

Figure 22. Receiver LCD during start of set-up mode.

A [DENS]

100%

B [DENS]

100%

C [DENS]

100%

SETUP IN 10 SECONDS

S&C RGDM Setup Mode
Used To Link Remotes
To Phases. To Start 
Press Button & Hold

Set-up button

Summary of Contents for 2000 series

























Reviews: