Samsung xpress m283 series Page 86 Service Manual Download

Page: 86 / 118

4. Troubleshooting

► Error Code

11-2T11

11-2T71

► Error message

Tray 1 Paper Mismatch

Manual Paper Mismatch

► Symptom

Paper option on Tray1 or Manual Feeder is incorrect.

► Troubleshooting method

1) Arrange paper on the Tray 1 and the Manual Feeder.

2) Check the paper options on Printer and Printer driver are same. If not, correct the options as same.

- Paper source

- Paper size

- Paper type

► Error Code

A1–1110

► Error message

Actuator Motor Failure : #A1-1110. Turn off then on.

► Symptom

After working the main BLDC motor, the Ready signal has not occurred within 1 sec.

► Troubleshooting method

※

First, turn the machine off then on. If the error persists, refer to the following.

1) Check if the motor connector on the main board is connected properly. Reconnect it.

2) OPC coupler has overloaded. After removing the toner cartridge, rotate the OPC coupler. (Spec : 6 kgf.cm) If there

is any damage, the OPC coupler can’t rotate well. Replace the toner cartridge.

3) The main BLDC motor is defective.

- Unplug the connector from the motor carefully.

- Replace the main BLDC motor with new one.

4) If the problem persists, replace the main board.

4-24

Summary of Contents for xpress m283 series



















































































































Search results

Summary of Contents for xpress m283 series

Reviews:

Related manuals for xpress m283 series

Brands by name

Popular brands

Samsung xpress m283 series, Service Manual

Search results

Summary of Contents for xpress m283 series

Reviews:

Related manuals for xpress m283 series

Brands by name

Popular brands