Samsung xpress m283 series Page 28 Service Manual Download

Page: 28 / 118

2. Product Specifications and Description

2.2.5. Hardware configuration

Xpress M283x series Electrical Circuit System consists of the following:

•

Main board (System board)

•

OPE board

•

SMPS board

•

HVPS board

Diagram of Xpress M283x series Electrical Circuit

Xpress M283x series has a system board of integrated engine controller and video controller.

The engine controller controls all modules required to print, that is, LSU, HVPS, SMPS, FAN, Fuser, etc.

It communicates with the video control block inside CPU for printing. And it has the interface for all video sync signal
to print out the video data.

The video controller receives print data from the host through network or USB Port. It takes this information and generates
printable video bitmap data.

The main board adopts the 600 MHz CPU, on board DDR3 memory (128MB) to perform printing jobs successfully.

2-17

Summary of Contents for xpress m283 series



















































































































Search results

Summary of Contents for xpress m283 series

Reviews:

Related manuals for xpress m283 series

Brands by name

Popular brands

Samsung xpress m283 series, Service Manual

Search results

Summary of Contents for xpress m283 series

Reviews:

Related manuals for xpress m283 series

Brands by name

Popular brands